Intellijel Tetrapad Скачать руководство пользователя страница 50

Страница: 50 / 63

10/30/2018

Tetrapad 2.0 Manual - Google Docs

https://docs.google.com/document/d/18AFrtwTCpaE5_dPILqmrodOXnIIEmdZGws2Kx_eEC4M/edit#heading=h.akbpz6132fpo

50/63

Tetrapad Manual

For example, one CW turn transposes the root note up 1 octave; a second CW turn
transposes the second note up 1 octave, and so on. Similarly, one CCW turn
transposes the fourth note down 1 octave; etc.

6. Touch each of the remaining three pads and repeat steps 3-6 to deﬁne 4-note chords for

each of the four pads.

Chord Name

Intervals

Unison

0, 0, 0, 0

Major w/octave

0, 4, 7, 12

Minor w/octave

0, 3, 7, 12

Major 7th

0, 4, 7, 11

Minor 7th

0, 3, 7, 10

Dominant 7th

0, 4, 7, 10

Diminished 7th

0, 3, 6, 9

Half-Diminished 7th

0, 3, 6, 10

Minor Major 7th

0, 3, 7, 11

Augmented Major 7th

0, 4, 8, 11

Augmented 7th

0, 4, 8, 10

Diminished Major 7th

0, 3, 6, 11

Dominant 7th ﬂat 5th

0, 4, 6, 10

Page 49

Содержание Tetrapad
































































Результаты поиска

Содержание Tetrapad

Отзывы:

Бренды по названию

Популярные бренды

Intellijel Tetrapad, Руководство пользователя

Результаты поиска

Содержание Tetrapad

Отзывы:

Бренды по названию

Популярные бренды