manualshive.com logo in svg

Intellijel Tetrapad, Руководство пользователя

Поделиться
Скачать
Intellijel Tetrapad Скачать руководство пользователя страница 18

10/30/2018

Tetrapad 2.0 Manual - Google Docs

https://docs.google.com/document/d/18AFrtwTCpaE5_dPILqmrodOXnIIEmdZGws2Kx_eEC4M/edit#heading=h.akbpz6132fpo

18/63

  

 

 

Tetrapad Manual

 

  

 

 

 

Note that the eight Output Status LEDs will change colors as you cycle through the 
modes. These colors indicate what type of signal appears at each output for each mode, 
and will be discussed further in the mode-specific sections of this manual. 

3. Rotate either of the two right encoders to select the desired preset within the selected 

mode. 

Each mode has 12 preset “slots,” as indicated by the Level LEDs embedded beneath the 
right-center pad. As you rotate one of the two right encoders, the brightly lit Level LED 
moves up/down accordingly, to indicate which of the 12 presets you’re about to load. The 
dimly lit LED indicates the location of the last used Mode Preset. 

NOTE: Each mode you select remembers that last preset used by that mode. So you 
only need to select a Mode Preset if you want to use one that’s different than the preset 
you used the last time you selected that mode.  

4. Press Encoder 3 to load the Mode Preset into Tetrapad. 

5. Press the white Mode Select button to exit mode selection. 

Your Tetrapad will now operate in this mode, using the selected preset. Note that you 
can also click either of the two left encoders to exit mode selection. 

Saving Mode Presets 

To save your current configuration to one of the twelve mode-specific presets: 

1. Configure your pads as desired. 

For example, assume you’re in Combo Mode and you configure Pad 1 and 2 to be 
unipolar faders, Pad 3 to be an LFO and Pad 4 to be a pair of switches, and you want to 
save this configuration for future use. 

2. Long-press (>1 second) the white Mode Select button to enter Mode Selection. 

Tetrapad will enter Mode Selection with the current mode already selected.  

3. Rotate either of the two right encoders to select the preset slot in which you want to save 

your configuration. 

4. Press Encoder 4 to Save the configuration as a mode preset. 

5. Press the white Mode Select button to exit mode selection. 

 

 

 

Page 17 

Содержание Tetrapad
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды