manualshive.com logo in svg

Intellijel Tetrapad, Руководство пользователя

Поделиться
Скачать
Intellijel Tetrapad Скачать руководство пользователя страница 25

10/30/2018

Tetrapad 2.0 Manual - Google Docs

https://docs.google.com/document/d/18AFrtwTCpaE5_dPILqmrodOXnIIEmdZGws2Kx_eEC4M/edit#heading=h.akbpz6132fpo

25/63

  

 

 

Tetrapad Manual

 

  

 

 

 

Assigning Bipolar Fader Functionality To A Pad 

To assign biplar fader functionality to one of Tetrapad’s four pads: 

1. Put Tetrapad into Combo Mode, as described in the 

Combo Mode

 section, earlier. 

2. Short-press (<1 sec) the white Mode Select button. 

The Level LEDs embedded beneath each pad will play an animation, indicating the 
function currently assigned to each pad. 

3. Rotate the encoder that corresponds to the pad you wish to make a Bipolar Fader. 

4. Stop rotating when the Bipolar Fader animation plays (as shown in the previous 

pictograph). 

5. Press the white Mode Select button to exit Pad assignment, and to use your Tetrapad. 

The two middle LEDs are lit on the assigned pad, indicating that it will now function as a 
Bipolar Fader (also shown in the previous pictograph). 

Using Bipolar Faders 

1. Slide a finger up and down a pad, just as if you were moving an actual fader. 

Alternately, you can simply tap a pad anywhere along its vertical scale and the fader will 
jump to that level directly (using a slew rate you define, as discussed shortly). Faders 
return to their null values when you lift your finger (unless you latch the fader by pressing 
the pad’s encoder). 

Tetrapad sends a fader’s vertical position CV to its left (odd numbered) output. If you 
touch the pad above center, the Output Status LED lights green (indicating a positive 
voltage). If you touch the pad below center, the Output Status LED lights red (indicating 
a negative voltage). The brightness of the LED indicates the absolute value of the 
voltage. 

2. Press down on a pad to send an additional pressure-sensitive CV to the pad’s right 

(even numbered) output. 

The Output Status LED lights cyan to indicate the presence of a pressure CV signal, 
while the brightness of the LED indicates its absolute value, from 0 to +5V. 

3. If you want to latch the fader, press the pad’s encoder. 

Latched faders are indicated by a blue Pad Status LED. When a fader is latched, it 
remains at the last level touched. When a fader is unlatched (the Status LED is off), it 
snaps back to its minimum value when you release it. 

 

Page 24 

Содержание Tetrapad
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды