Intellijel Stereo Line In 1U Скачать руководство пользователя страница 3

  
 

 

Stereo   Line   In   1U   System   Manual 

 

 
 

 

Compliance  

 

This   device   complies   with   Part   15   of   the   FCC   Rules.   Operation   is   subject   to   the  
following   two   conditions:   (1)   this   device   may   not   cause   harmful   interference,   and  
(2)   this   device   must   accept   any   interference   received,   including   interference   that  
may   cause   undesired   operation.  

Changes   or   modifications   not   expressly   approved   by   Intellijel   Designs,   Inc.   could  
void   the   user’s   authority   to   operate   the   equipment.  

Any   digital   equipment   has   been   tested   and   found   to   comply   with   the   limits   for   a  
Class   A   digital   device,   pursuant   to   part   15   of   the   FCC   Rules.   These   limits   are  
designed   to   provide   reasonable   protection   against   harmful   interference   when   the  
equipment   is   operated   in   a   commercial   environment.   This   equipment   generates,  
uses,   and   can   radiate   radio   frequency   energy   and,   if   not   installed   and   used   in  
accordance   with   the   instruction   manual,   may   cause   harmful   interference   to   radio  
communications.  

 

 

 

This   device   meets   the   requirements   of   the   following   standards   and   directives:  

EMC:    2014/30/EU  
EN55032:2015   ;   EN55103-2:2009   (EN55024)   ;   EN61000-3-2   ;   EN61000-3-3   

Low   Voltage:   2014/35/EU  
EN   60065:2002+A1:2006+A11:2008+A2:2010+A12:2011   

RoHS2:   2011/65/EU  

WEEE:   2012/19/EU  

 

 

 

 

Page   2  

Содержание Stereo Line In 1U
















Отзывы: