manualshive.com logo in svg

Intellian v1-130 series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Intellian v1-130 series Скачать руководство пользователя страница 97

97

REMOTE WEB ACCESS

No.

Item

Description 

 

1

Parameter Setting 

Set antenna search & tracking parameters. 
These parameters should only be changed by an authorized 
service technician. Improper setting of these parameters will 
render your system inoperable.

 

2

Search & Tracking 
Parameter Setting

DVB Detect and Tracking Level Threshold: display/set current 
detect level threshold and tracking level threshold when DVB 
tracking mode is chosen to be used.
- NBD Detect and Tracking Level Threshold: display/set 

current detect level threshold and tracking level threshold 
when NBD tracking mode is chosen to be used.

- Enable Threshold: display/set TX enable threshold.
- Wait time: set the time-out for automatic initiation of a search 

after the signal level drops below the pre-defined threshold 
value.

- Search Step: set increment step size. 
- Search 1 & 3 Range: set Search 1 & 3 search range. Search 

is conducted in a two-axis pattern consisting of alternate 
movements in azimuth and elevation as forming expanding 
square.

- Search 2 Range: is reserved for future use.

 

3

Tilt Sensor Bias 

Adjust the two solid-state tilt sensors used to provide absolute 
cross-level tilt of the antenna and elevation feedback to 
eliminate long-term pointing drift (error). Tilt bias is required to 
be adjusted when the antenna control board or sensor box is 
replaced. Check to see whether or not the bubble is located at 
the center of the level vial.

 

4

Elevation Adjust 

Adjust the angle difference between the mechanical elevation 
angle and actual elevation angle.

 

5

Conical Range

Set conical range while the antenna is on tracking mode.

 

6

Rate Sensor 
Adjust

Calibrate DC voltage output from the three rate sensors used 
to sense antenna motion in azimuth, elevation and cross-level 
axes. During the calibration process, the antenna should avoid 
any motion as it can affect the antenna’s performance.

 

7

Idle Mode 

Release the elevation and cross level motor brakes while 
the antenna is in SETUP mode. The antenna can be moved 
manually during the idle mode.

 

8

Reboot

Reboot the system. 

Содержание v1-130 series
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды