Intellian v1-130 series Скачать руководство пользователя страница 84

Страница: 84 / 119

v130 – Marine Satellite Communication System

Version, Tracking Parameter & Block Zone

Display the antenna, ACU firmware versions and serial number.
Setup the antenna blockage zone(s).
Setup the antenna parameters.

Display antenna versions

and tracking parameters

Software Information

- Software information: Display antenna and ACU firmware versions and library

version.

Product Information

- Product information: Display antenna and ACU serial numbers.

Parameter Setting

- DVB: Display /setup current detect level threshold and tracking level threshold

when DVB tracking mode is chosen to be used.

- NBD: Display /setup current detect level threshold and tracking level threshold

when NBD tracking mode is chosen to be used.

- TX Enable Threshold: display/ setup TX enable threshold.

Block Zone

- Display current block zones by azimuth and elevation sectors. Up to 5 blockage

zones can be programmed.

NOTE:

DVB and NBD parameter settings should only be changed by an authorized service technician.

Improper setting of these parameters will render your system inoperable. Consult Intellian for changing
antenna parameters.

Содержание v1-130 series
























































































































Результаты поиска

Содержание v1-130 series

Отзывы:

Бренды по названию

Популярные бренды

Intellian v1-130 series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание v1-130 series

Отзывы:

Бренды по названию

Популярные бренды