manualshive.com logo in svg

Intellian v1-130 series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Intellian v1-130 series Скачать руководство пользователя страница 19

19

INSTALLING THE ANTENNA

Planning the Installation

Selection of Antenna Installation Site

Install the antenna in accordance with the following procedures to insure maximum 
performance of the antenna. The ideal antenna site has a clear view of the horizon 
or satellite all around. Please be sure there are no obstacles within 15º above the 
center of the antenna. Any obstacles can prevent the antenna from transmitting and 
receiving the satellite signal.

Do not install the antenna near the radar especially on the same plane as its energy 
levels may overload the antenna front-end circuits. It is recommended to position 
the antenna at least 4 feet (1.2 m) above or below the level of the radar and minimum 
of 15 feet (4.6 m) away from the high power short wave radars.

The mounting platform should be rigid enough and not subjected to excessive 
vibration. The movement of the antenna can be minimized by installing at the 
center of the vessel. If these conditions can be only partially satisfied, find the best 
compromised installation site between the various considerations.

Elevation Limit 

of Obstacles

15°

Configure Radiation Hazard/Blockage Zones 

It is important to setup the radiation hazard or blockage zones for Intellian VSAT 
communication systems. The ACU can be programmed with relative azimuth and 
elevation sectors to create up to five zones where transmit power would endanger 
personnel who are frequently in that area or blockage exists. Several things happen 
when the antenna is within one of these zones.

1.

 “BLOCK” will be displayed on the ACU screen.

2.

 Tracking continues as long as the signal level is greater than the predefined 

threshold value. When the signal level drops below the threshold value the 
antenna will wait “Search Wait Time” parameter amount of time and re-target the 
satellite you targeted last. The antenna will continue to re-target the satellite until 
the satellite is re-acquired and tracking can be resumed.

3.

 A transmit inhibit output from the ACU will disable/mute the modem transmission.

Antenna Unit

Obstacle

Содержание v1-130 series
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды