Intel VIA K8T800 Скачать руководство пользователя страница 53

Страница: 53 / 92

BIOS

Page 4-19

USB Resume from S3

This item allows a USB device to wake-up the system from S3 suspend state.
Options: Enabled, Disabled.

PowerOn by PCI Card

An input signal from PME on the PCI card awakens the system from soft-off state.
Options: Enabled, Disabled.

PowerOn by OnBoard LAN

This item allows you to power on the system by onboard LAN from soft-off state.
Options: Enabled, Disabled.

Modem Ring Resume

When set to Enabled, any event occurring to the Modem Ring will awaken the
system from suspend state.
Options: Enabled, Disabled.

RTC Alarm Resume

When set to Enable rtc alarm resume, you can set the date (of month) and time (hh:
mm:ss), that will awaken a system which has been powered down.

Содержание VIA K8T800





























































































Результаты поиска

Содержание VIA K8T800

Отзывы:

Похожие инструкции для VIA K8T800

Бренды по названию

Популярные бренды

Intel VIA K8T800, Руководство пользователя

Результаты поиска

Содержание VIA K8T800

Отзывы:

Похожие инструкции для VIA K8T800

Бренды по названию

Популярные бренды