Intel VIA K8T800 Скачать руководство пользователя страница 44

Страница: 44 / 92

BIOS

Page 4-10

LDT & PCI Bus Control

Scroll to LDT & PCI Bus Control and press <Enter>. The following screen appears:

Upstream LDT Bus Width

Options: 8 bit, 16 bit.

Downstream LDT Bus Width

Options: 8 bit, 16 bit.

LDT Bus Frequency

This item sets CPU Hyper Transport front size bus.
Options: Auto, 800MHz, 600MHz, 400MHz, 200MHz.

PCI1/2 Master 0 WS Write

When Enabled, Writes to the PCI bus are commanded with zero wait states.
Options: Enabled, Disabled.

PCI1/2 Post Write

Enables CPU to PCI bus POST write.
Options: Enabled, Disabled.

PCI Delay Transaction

The chipset has an embedded 32-bit posted write buffer to support delay transactions
cycles. Select Enabled to support compliance with PCI specification version 2.2.
Options: Enabled, Disabled.

Содержание VIA K8T800





























































































Результаты поиска

Содержание VIA K8T800

Отзывы:

Похожие инструкции для VIA K8T800

Бренды по названию

Популярные бренды

Intel VIA K8T800, Руководство пользователя

Результаты поиска

Содержание VIA K8T800

Отзывы:

Похожие инструкции для VIA K8T800

Бренды по названию

Популярные бренды