Intel SCB2 - Server Board Motherboard Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 108

background image

41

4 Configuration Software and Utilities

Service Partition (Optional)

When you are setting up your server system, you can install a service partition onto your hard drive.
The service partition includes utilities, and other software that be run locally or remotely to assist in
system management. The service partition uses approximately 30 to 40 MB of hard disk space.

✏

NOTE

It is highly recommended that you install the service partition before
installing an operating system. For more information, see the Service
Partition section in the Installation Guide for the Intel Server Control. This
document is included on the Resource CD-ROM shipped with your SCB2
server board.

Configuration Utilities

System Software Update Sequence

When you update the system software, you should do it in the following order.

1. Update

BIOS

2. Update firmware (BMC & HSC)
3. Update

FRU/SDR

4. Unplug system for 30 seconds
5. Clear CMOS via front panel

«
...
39
40
41
42
43
...
»

Содержание SCB2 - Server Board Motherboard













































































































Отзывы:

Нет отзывов

Похожие инструкции для SCB2 - Server Board Motherboard

Enterprise Server S80

Бренд: IBM Страницы: 282

Бренд: Avaya Страницы: 19

Бренд: Vecow Страницы: 122

UltraNEXUS-HD Flex

Бренд: Leightronix Страницы: 5

Бренд: Buffalo Страницы: 2

BocaVision WT120

Бренд: Boca Systems Страницы: 28

EonServ 7000 Series

Бренд: Infotrend Страницы: 2

Бренд: SEH Страницы: 32

SUPERSERVER 6113L-8

Бренд: Supero Страницы: 104

SUPERSERVER 6017R-NTF

Бренд: Supero Страницы: 126

SuperServer 5017R-MF

Бренд: Supero Страницы: 106

SUPERSERVER 5015A-EHF

Бренд: Supero Страницы: 106

SuperServer 5013S-8

Бренд: Supero Страницы: 110

Supero SUPERSERVER 5015B-NT

Бренд: Supero Страницы: 98

Бренд: Supero Страницы: 122

Бренд: Supero Страницы: 121

SuperStorage L-Serie

Бренд: Supermicro Страницы: 1

Бренд: Supermicro Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды