Intel SCB2 - Server Board Motherboard Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 108

background image

Description

13

The network controller provides several options for increasing throughput and fault tolerance when
running Windows NT

†

4.0, Windows

†

2000 , NetWare

†

4.1x or newer, or Linux

†

:

•

Adapter Fault Tolerance (AFT) - provides automatic redundancy for your adapter. If the
primary adapter fails, the secondary takes over. AFT works with any hub or switch.

•

Adaptive Load Balancing (ALB) - creates a team of 2 - 8 adapters to increase transmission
throughput. Also includes AFT. Works with any 10Base-TX or 100Base-TX switch.

•

Fast EtherChannel

†

(FEC) or Intel

®

Link Aggregation - creates a team of up to 8 adapters to

increase transmission and reception throughput. Also includes AFT. Requires a FEC-enabled
switch.

To set up an option, read the instructions in the Windows NT 4.0 or NetWare 4.1x readme files.

General Configuration Notes

1. Windows NT versions prior to 4.0 do not support Adapter Teaming options.
2. Adapter Teaming options require NT 4.0 with Service Pack 4.0 or Service Pack 3.0 and the

Windows Hot Fix

†

.

3. In Windows NT, teaming options cannot be implemented on adapters that have been

configured for VLANs. NetWare can support teaming options and VLANs on the same
adapters.

Adapter Fault Tolerance

Adapter Fault Tolerance (AFT) is a simple, effective, and fail-safe approach to increase the
reliability of server connections. AFT gives you the ability to set up link recovery to the server
adapter in case of a cable, port, or network interface card failure. By assigning two server adapters
as a team, AFT enables you to maintain uninterrupted network performance.

AFT is implemented with two server adapters: a primary adapter and a backup, or secondary,
adapter. During normal operation, the backup will have transmit disabled. If the link to the
primary adapter fails, the link to the backup adapter automatically takes over.

Preferred Primary Adapter

With multiple adapters installed, you can specify one as the Preferred Primary adapter. For
example if you have a server with a PRO/1000 server adapter as the primary adapter and a
PRO/100+ adapter as the secondary, you could configure the PRO/1000 server adapter to be the
preferred primary. In this scenario, if the PRO/1000 server adapter fails, the PRO/100+ will take
over. Then when the PRO/1000 server adapter is replaced, it will automatically revert to being the
primary adapter in the team.

If a Preferred Primary is not selected, PROSet will attempt to select the best adapter, based on
adapter model and speed.

Mixed Adapter Teaming

AFT supports up to eight server adapters per team, in any mix.

«
...
11
12
13
14
15
...
»

Содержание SCB2 - Server Board Motherboard













































































































Отзывы:

Нет отзывов

Похожие инструкции для SCB2 - Server Board Motherboard

Бренд: Acano Страницы: 17

Power 720 Express 8202-E4B

Бренд: IBM Страницы: 64

Бренд: IBM Страницы: 148

Бренд: IBM Страницы: 36

Бренд: IBM Страницы: 834

Бренд: Sun Fire Страницы: 66

BladeCenter HS20 Type 8843

Бренд: IBM Страницы: 112

Бренд: Advantech Страницы: 43

Windows Server 2008 R2

Бренд: HP Страницы: 18

TruCluster Server V5.1B-1

Бренд: HP Страницы: 19

Бренд: HP Страницы: 24

Virtual Connect FlexFabric-20/40 F8 Module

Бренд: HP Страницы: 23

ProLiant SL335s G7

Бренд: HP Страницы: 2

Бренд: HP Страницы: 36

ProLiant SL2500 Gen8

Бренд: HP Страницы: 4

Бренд: HP Страницы: 11

ProLiant XL250a Gen9

Бренд: HP Страницы: 34

ProLiant XL450 Gen10

Бренд: HP Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды