Intel SCB2 - Server Board Motherboard Скачать руководство пользователя страница 23

Страница: 23 / 108

Installation Procedures

Server Board Bumpers

If you are installing your server board in a non-Intel chassis, you must provide and install rubber
bumpers at the locations shown below. They must be the same height as the existing board mount
standoffs.

CAUTION

You must install rubber bumpers in all non Intel

chassis that do not already

support the board at the locations shown in the illustration.

The rubber bumpers you provide and install must be the same height as the
existing board mount standoffs to properly support your new board.

Failure to install bumpers, or installing bumpers that are too tall or too short,
may damage your board.

DO NOT INSTALL server board bumpers in the Intel SR1200 and
SR2200 server chassis.

OM12372

11.0 inches

[280.0]

3.8 inches

[97.0]

3.6 inches

[85.0]

2.7 inches

[70.0]

5.9 inches

[150.0]

Figure 7. Installing Server Board Bumpers

Содержание SCB2 - Server Board Motherboard













































































































Результаты поиска

Содержание SCB2 - Server Board Motherboard

Отзывы:

Похожие инструкции для SCB2 - Server Board Motherboard

Бренды по названию

Популярные бренды

Intel SCB2 - Server Board Motherboard, Руководство по эксплуатации продукта

Результаты поиска

Содержание SCB2 - Server Board Motherboard

Отзывы:

Похожие инструкции для SCB2 - Server Board Motherboard

Бренды по названию

Популярные бренды