Intel SC5299-E BRP Скачать руководство пользователя

Страница: 67 / 168

Hardware Installations and Upgrades

Intel® Entry Server Chassis SC5299-E DP/WS/BRP User Guide

Replacing a Hot Swap Power Supply Cage (BRP

configuration only)

Warning: Hazardous conditions, power supply: Hazardous voltage, current, and energy levels are

present inside the power supply. There are no user-serviceable parts inside it; servicing of
the power supply should be done by technically qualified personnel.

1. Observe the safety and ESD precautions listed in

Appendix A, “Safety Information”

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the left side cover. For instructions, see

“Removing the Left Side Cover”

4. Press up on green latch (see letter “A”) while pulling on handle to remove hot swap

power supply module from chassis.

Figure 62. Removing Hot Swap Power Supply Module

5. Remove second (redundant) hot swap power supply module (or filler panel), if one is

present.

6. Disconnect all internal power cables from chassis components and server board.

TP01765

Содержание SC5299-E BRP









































































































































































Результаты поиска

Содержание SC5299-E BRP

Отзывы:

Похожие инструкции для SC5299-E BRP

Бренды по названию

Популярные бренды

Intel SC5299-E BRP, Руководство пользователя

Результаты поиска

Содержание SC5299-E BRP

Отзывы:

Похожие инструкции для SC5299-E BRP

Бренды по названию

Популярные бренды