Intel SC5299-E BRP Скачать руководство пользователя

Страница: 65 / 168

Hardware Installations and Upgrades

Intel® Entry Server Chassis SC5299-E DP/WS/BRP User Guide

Installing an Additional Hot Swap Power Supply Module

(BRP configuration only)

Note: This install procedure only applies to a chassis with redundant power supply capability.

DO NOT perform this install procedure if your chassis has a fixed power supply

Warning: Hazardous conditions, power supply: Hazardous voltage, current, and energy levels are

present inside the power supply. There are no user-serviceable parts inside it; servicing of
the power supply should be done only by technically qualified personnel.

1. Observe the safety and ESD precautions listed in

Appendix A, “Safety Information”

2. Insert finger into hole in middle of filler panel and remove filler panel from chassis.

Figure 58. Removing Power Supply Filler Panel

3. Insert new hot swap power supply module until it clicks into place.

Figure 59. Inserting Additional Hot Swap Power Supply Module

TP00916

TP00917

Содержание SC5299-E BRP









































































































































































Результаты поиска

Содержание SC5299-E BRP

Отзывы:

Похожие инструкции для SC5299-E BRP

Бренды по названию

Популярные бренды

Intel SC5299-E BRP, Руководство пользователя

Результаты поиска

Содержание SC5299-E BRP

Отзывы:

Похожие инструкции для SC5299-E BRP

Бренды по названию

Популярные бренды