Intel S3000AH Скачать руководство пользователя страница 30

Страница: 30 / 74

Intel

Server Board S3000AH User’s Guide

Configuration Jumpers

Figure 6. Configuration Jumper Descriptions

Jumper Name

Jumper Purpose

NIC1 NVM Protect Mode

Jumper in default position (pins 1-2) protects the Intel

82573E/V

firmware from being programmed.

Jumper in update mode (pins 2-3) allows the Intel

82573E/V

firmware to be programmed.

CMOS Clear

Jumper in normal position (pins 1-2) allows the system to

successfully POST and boot to the OS environment. BIOS settings

are kept intact.

Jumper in clear position (pins 2-3) initiates a clearing of NVRAM

following POST. A system message confirms the CMOS clear

operation was successful. This setting enforces default BIOS

settings, which can be changed by entering setup via F2, then

exiting setup via F10 and saving changes.

System Maintenance

Mode

Jumper in normal position (pins 1-2) allows normal system

operation with correct BIOS settings. System will POST normally.

Jumper in maintenance mode (pins 2-3) allows Intel

AMT setting/

password reset.

Jumper removed is used to recover from a corrupted BIOS.

Bootable media with a valid BIOS ROM required.

AF000525

Default

CLEAR
CMOS

J1G3

CMOS

CLR

J4A1

Default

Update

NIC1
NVM

Protect

Mode

J1H3

Default

System

Maintenance

Mode

Remove jumper for BIOS recovery

Содержание S3000AH











































































Результаты поиска

Содержание S3000AH

Отзывы:

Похожие инструкции для S3000AH

Бренды по названию

Популярные бренды

Intel S3000AH, Руководство пользователя

Результаты поиска

Содержание S3000AH

Отзывы:

Похожие инструкции для S3000AH

Бренды по названию

Популярные бренды