Intel Pga478 - P4-2ghz 512kb 400mhz Fsb Скачать руководство пользователя страница 15

Страница: 15 / 68

Intel

Celeron

Processor 1.66 GHz/1.83 GHz

January 2007

Order Number: 315876-002

Electrical Specifications—Intel

Celeron

Processor 1.66 GHz/1.83 GHz

3.0

Electrical Specifications

3.1

Front Side Bus and GTLREF

Most Intel

Celeron

Processor 1.66 GHz/1.83 GHz FSB signals use Advanced Gunning

Transceiver Logic (AGTL+) signalling technology. This signalling technology provides

improved noise margins and reduced ringing through low-voltage swings and controlled

edge rates. The termination voltage level for the Intel

Celeron

Processor 1.66 GHz/

1.83 GHz AGTL+ signals is V

CCP

= 1.05 V (nominal). Due to speed improvements to

data and address bus, signal integrity and platform design methods have become more

critical than with previous processor families.

The AGTL+ inputs require a reference voltage (GTLREF) that is used by the receivers to

determine if a signal is a logical 0 or a logical 1. GTLREF must be generated on the

system board. Termination resistors are provided on the processor silicon and are

terminated to its I/O voltage (V

CCP

The AGTL+ bus depends on incident wave switching. Therefore, timing calculations for

AGTL+ signals are based on flight time as opposed to capacitive deratings. Analog

signal simulation of the FSB, including trace lengths, is highly recommended when

designing a system.

3.2

Power and Ground Pins

For clean, on-chip power distribution, the Intel

Celeron

Processor 1.66 GHz/1.83

GHz has a large number of V

(power) and V

(ground) inputs. All power pins must be

connected to V

power planes while all V

pins must be connected to system ground

planes. Use of multiple power and ground planes is recommended to reduce IR drop.

The processor V

pins must be supplied with the voltage determined by the VID

(Voltage ID) pins.

3.3

Decoupling Guidelines

Due to its large number of transistors and high internal clock speeds, the processor is

capable of generating large average current swings between low and full power states.

This may cause voltages on power planes to sag below their minimum values if bulk

decoupling is not adequate. Care must be taken in the board design to ensure that the

voltage provided to the processor remains within the specifications listed in

Table 7

Failure to do so can result in timing violations or reduced lifetime of the component.

3.3.1

Decoupling

Regulator solutions need to provide bulk capacitance with a low effective series

resistance (ESR) and keep a low interconnect resistance from the regulator to the

socket. Bulk decoupling for the large current swings when the part is powering on, or

entering/exiting low-power states, must be provided by the voltage regulator solution.

For more details on decoupling recommendations, please refer to the

Embedded

Voltage Regulator-Down (EmVRD) 11.0 Design Guidelines for Embedded

Implementations Supporting PGA478

Содержание Pga478 - P4-2ghz 512kb 400mhz Fsb





































































Результаты поиска

Содержание Pga478 - P4-2ghz 512kb 400mhz Fsb

Отзывы:

Похожие инструкции для Pga478 - P4-2ghz 512kb 400mhz Fsb

Бренды по названию

Популярные бренды

Intel Pga478 - P4-2ghz 512kb 400mhz Fsb, Техническое описание

Результаты поиска

Содержание Pga478 - P4-2ghz 512kb 400mhz Fsb

Отзывы:

Похожие инструкции для Pga478 - P4-2ghz 512kb 400mhz Fsb

Бренды по названию

Популярные бренды