Intel D946GZTS - Desktop Board Motherboard Скачать руководство пользователя страница 9

Страница: 9 / 76

1 Desktop Board Features

This chapter briefly describes the main features of Intel

Desktop Board D946GZTS.

Table 1 summarizes the major features of the desktop board.

Table 1. Feature Summary

Form Factor

microBTX (264.16 millimeters [10.40 inches] x 266.70 millimeters
[10.50 inches])

Processor

Support for an Intel

processor in the LGA775 package

Main Memory

•

Two 240-pin, DDR2 1.8 V SDRAM Dual Inline Memory Module (DIMM)

sockets

•

667/533 MHz single or dual channel DDR2 SDRAM interface

•

Support for up to 4 GB of system memory

Chipset

Intel

946GZ Express Chipset consisting of:

•

Intel

946GZ Express Chipset Graphics and Memory Controller Hub

(GMCH)

•

Intel

82801GB I/O Controller Hub (ICH7)

Graphics

•

Intel

946GZ Express Chipset with

Intel

Graphics Media Accelerator 3000

(Intel

GMA 3000)

•

PCI Express* graphics card support via a PCI Express x16 connector

Audio

•

6-channel (5.1) onboard subsystem, featuring:

―

Intel

High Definition Audio interface

―

SigmaTel* STAC9227 audio codec

―

HD Audio Link header

Expansion
Capabilities

•

One PCI Express x1 connector

•

One PCI Express x16 connector

•

Two PCI connectors

Peripheral

Interfaces

•

Up to eight USB 2.0 ports

―

Four ports routed to the back panel

―

Four ports routed to two USB headers

•

Four Serial ATA (SATA) channels (3.0 Gb/s), via the ICH7, one device per

channel

•

One IDE interface with ATA-66/100 support (two devices)

•

One diskette drive interface

•

One VGA port

•

One parallel port

•

One serial port

•

PS/2* keyboard and mouse ports

continued

Содержание D946GZTS - Desktop Board Motherboard













































































Результаты поиска

Содержание D946GZTS - Desktop Board Motherboard

Отзывы:

Intel D946GZTS - Desktop Board Motherboard, Руководство по эксплуатации продукта, Страница: 9 / 76

Результаты поиска

Содержание D946GZTS - Desktop Board Motherboard

Отзывы: