Intel 80331 Скачать руководство пользователя страница 50

Страница: 50 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.4

Embedded PCI-X 133 MHz Alternate Topology

This section lists another embedded topology with routing recommendations for PCI-X 133 MHz.

Figure 19

shows the block diagram of this topology and

Table 11

describes the routing

recommendations.

Figure 19.

Embedded PCI-X 133 MHz Alternate Topology

Table 11.

Embedded PCI-X 133 MHz Alternate Topology Routing Recommendations

Parameter

Routing Guideline for Lower AD Bus

Reference Plane

Preferred Layer

Route over an unbroken ground plane

Stripline

Break out

5 mils on 5 mils spacing. Maximum length of breakout region is 500 mils

Motherboard impedance
(both Microstrip and stripline)

50 ohms +/- 15%

Add-in card impedance (both
Microstrip and stripline)

60 ohms +/- 15%

Stripline Trace Spacing

12 mils edge to edge

Microstrip Trace Spacing

18 mils, edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum edge to edge

Trace Length 1 (TL1): From
80331 signal Ball to first
device

1.5” minimum - 3.5” maximum

Trace Length 3 TL2: First
device to second device.

1.5” minimum - 3.5” maximum

Length Matching
Requirements:

No length matching is required among datalines. For length matching for clocks,
refer clock guidelines

Table 8

Number of vias

Three vias for each path

TL1

EM1

EM2

TL2

Содержание 80331





















































































































































Результаты поиска

Содержание 80331

Отзывы:

Похожие инструкции для 80331

Бренды по названию

Популярные бренды

Intel 80331, Руководство по конструкции

Результаты поиска

Содержание 80331

Отзывы:

Похожие инструкции для 80331

Бренды по названию

Популярные бренды