Intel 3200 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 58

background image

Intel® 3210 and 3200 Chipset Thermal/Mechanical Design Guide

19

Thermal Metrology

5

Thermal Metrology

The system designer must make temperature measurements to accurately determine
the thermal performance of the system. Intel has established guidelines for proper
techniques to measure the MCH IHS temperatures.

provides guidelines on

how to accurately measure the MCH case temperature.

5.1

MCH Case Measurement

Intel

®

3210 and 3200 Chipset cooling performance is determined by measuring the

case temperature using a thermocouple. For case temperature measurements, the
attached method outlined in this section is recommended for mounting a
thermocouple.

Special case is required when measuring case temperature (Tc) to ensure an accurate
temperature measurement. Thermocouples are often used to measure Tc. When
measuring the temperature of a surface that is at a different temperature from the
surrounding local ambient air, errors may be introduced in the measurements. The
measurement errors can be caused by poor thermal contact between the thermocouple
junction and the surface of the integrated heat spreader, heat loss by radiation,
convection, by conduction through thermocouple leads, or by contact between the
thermocouple cement and the heatsink base. To minimize these measurement errors,
the approach outlined in the next section is recommended.

5.1.1

Supporting Test Equipment

To apply the reference thermocouple attach procedure, it is recommended that you use
the equipment (or equivalent) given in

Table 5-1.

Thermocouple Attach Support Equipment (Sheet 1 of 2)

Item

Description

Part Number

Measurement and Output

Microscope

Olympus* Light microscope or equivalent

SZ-40

DMM

Digital Multi Meter for resistance

measurement

Fluke 79 Series

Thermal Meter

Hand held thermocouple meter

Multiple Vendors

Test Fixtures (see notes for ordering information)

Special Modified Tip Solder

Block Fixture

40 W 120 V~60 Hz modified soldering

iron

Weller SP40L solder tool

Miscellaneous Hardware (see notes for ordering information)

Solder

Indium Corp. of America
Alloy 57BI/42SN/1AG 0.010 Diameter

52124

Flux

Indium Corp. of America

5RMA

Loctite* 498 Adhesive

Super glue w/ thermal characteristics

49850

Adhesive Accelerator

Loctite 7452 for fast glue curing

18490

Kapton* Tape

for holding thermocouple in place

Thermocouple

Omega*, 36 gauge, T type
(see note 2 for ordering information)

OSK2K1280/5SR TC-TT-T-36-72

«
...
17
18
19
20
21
...
»

Содержание 3200



























































Отзывы:

Нет отзывов

Похожие инструкции для 3200

Cyclone IV GX FPGA

Бренд: Altera Страницы: 60

Бренд: AOpen Страницы: 8

Бренд: Biostar Страницы: 71

Бренд: Gigabyte Страницы: 31

Бренд: Infineon Страницы: 20

Бренд: Foxconn Страницы: 108

Бренд: Aaeon Страницы: 78

Бренд: Zamel Страницы: 3

Бренд: Texas Instruments Страницы: 13

Бренд: MiTAC Страницы: 91

Бренд: Texas Instruments Страницы: 34

Бренд: DataExpert Страницы: 44

Бренд: IEI Technology Страницы: 158

Бренд: CML Страницы: 26

Бренд: Avalue Technology Страницы: 39

Бренд: Avalue Technology Страницы: 54

Бренд: Avalue Technology Страницы: 81

WOLFDALE1333-GLAN

Бренд: ASROCK Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды