14
Connect to devices with multichannel output
By connecting a DVD player, MPEG decoder, or other component
that has a multi channel port, you can playback the audio with 5.1
channel output. So, be sure to prepare a cable that can properly
connect the DTR-5.2 to the peripheral device.
Cautions regarding the AC OUTLETS
connectors
The DTR-5.2 is supplied with AC mains outlets for connecting the
power cords from other devices so that their power is supplied
through the DTR-5.2. By doing this, you can use the Standby/On
button on the DTR-5.2 to turn on and off the connected devices as
well.
Caution:
Make sure that the total capacity of the other components connected
to this unit does not exceed the capacity that is printed on the rear
panel. For this model, the capcity is 120 watts.
AC OUTLETS
AC 120 V 60 Hz
SWITCHED
TOTAL 120 W 1 A MAX.
DTR-5.2 MULTI CHANNEL INPUT
GND
OPTICAL
COAX
1
2
DIGITAL INPUT
CENTER
SUB
WOOFER
FRONT
SURR
SUBWOOFER
PRE OUT
L
R
MULTI
CHANNEL INPUT
L (White)
R (Red)
R (Red)
L (White)
Center output
Front output
Surround output
Subwoofer output
DVD Player/MPEG decoder
Connect to devices with
z
terminals
The
z
terminal on the DTR-5.2 is for connecting other Integra/
Onkyo components equipped with the same
z
terminal. When a
component are
z
-connected, you can point the remote controller
supplied with the DTR-5.2 at the sensor on the DTR-5.2 and operate
that component without having to switch remote controllers.
In addition, by connecting components to the
z
terminal, you can
also perform the system operations given below.
Power on/ready function
When the DTR-5.2 is in the standby state, if an
z
-connected
component is turned on, then the DTR-5.2 also turns on and the input
source selected at the DTR-5.2 automatically switches to that
component.
If the power cord for an
z
-connected component is connected to
the AC OUTLET on the DTR-5.2, or if the DTR-5.2 is turned on,
this function will not work.
Direct change function
When the play button is pressed at an
z
-connected component, the
input source selected at the DTR-5.2 automatically changes to that
component.
Power off function
When the DTR-5.2 is placed in the standby state, all
z
-connected
components are also automatically put into the standby state.
CAUTION
If an MD recorder is connected to the TAPE jack on the DTR-5.2,
switch the Input Selector from TAPE to MD (see page 18).
REMOTE
CONTROL
DTR-5.2
Ex: Integra/Onkyo CD player
z
connector
Ex: Integra/Onkyo cassette
tape deck
z
connector
Connections
To connect components using the
z
terminal, simply connect a
remote control cable from this
z
terminal to the
z
terminal of the
other component. An
z
remote control cable with a 1/8-inch (3.5-
mm) miniature two-conductor plug comes with every cassette tape
deck, compact disc player, MD recorder, and DVD player that has an
z
terminal.
• For remote control operation, the audio connection cables must
also be connected.
• The RC-441M remote controller does not support turntables.
• If a component has two
z
terminals, you can use either one to
connect to the DTR-5.2. The other one can be used to daisy chain
with another component.
• With Integra/Onkyo DVD players, you can enter the pre-
program code so that you can operate the DVD player directly
with the remote controller without connecting the
z
terminals
(see page 38).
