Integra DTR-30.2, Инструкция по эксплуатации

Страница: 62 / 84

62
En
If you’ve connected your Zone 2 speakers to the AV
receiver, as explained in “Connecting Your Zone 2 Speak-
ers Directly to the AV receiver” (
➔
61 ), you must set the
“ Front High / Front Wide / Zone 2 ” setting to “ Zone 2 ”.
Menu Speaker Setup
Note
• When “ Zone 2 ” is selected and Zone 2 turned on, the Zone 2
speakers connected to the FRONT HIGH OR FRONT WIDE
OR ZONE 2 SPEAKERS L/R terminals output sound, but the
surround back speakers, front high or front wide speakers con-
nected to the
SURR BACK OR FRONT HIGH OR FRONT
WIDE SPEAKERS L/R terminals do not. When “ Zone 2 ” is
selected and Zone 2 turned off, the surround back, front high and
front wide speakers output sound as normal.
• When the “ Front High / Front Wide / Zone 2 ” setting is set to
“ Zone 2 ” and the input selector of Zone 2 is selected, power con-
sumption on standby mode slightly increases.
• Powered Zone 2 cannot be used if “ Speakers Type (Front) ” is
set to “ Bi-Amp ” (
➔
46
).
Note
• This procedure can also be performed on the AV receiver by
using its Setup , arrow, and Enter .
■
Zone 2 Out
If you
’
ve connected your Zone 2 speakers to an amp with
no volume control, set the
“ Zone 2 Out ”
setting, respec-
tively, to
“ Variable ”
so that you can set the zone
’
s volume,
balance, and tone on the AV receiver.
`
Fixed :
The Zone 2 volume must be set on the amp in that
zone.
`
Variable :
The Zone 2 volume can be set on the AV receiver.
■
Zone 2 Maximum Volume
`
Off, 50 to 99 (Absolute display)
`
Off, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume.
To disable this setting, select “
Off ”.
■
Zone 2 Power On Volume
`
Last , Min , 1 to 99 or Max (Absolute display)
`
Last , –
Q
dB , –81dB to +18dB (Relative display)
With this preference, you can specify the volume set-
ting to be used each time the AV receiver is turned
on.
To use the same volume level that was used when the AV
receiver was turned off, select “
Last ”.
The “ Zone 2 Power On Volume ” cannot be set higher
than the “ Zone 2 Maximum Volume ” setting.
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust the
volume for Zone 2.
Controlling Zone 2 from the AV receiver
Note
• While Powered Zone 2 is being used, listening modes that
require surround back speakers or front high speakers or front
Setting the Powered Zone 2
1
In the “Speaker Setup” menu, select “Speaker
Settings”, and then press
Enter .
2
Use
q
/
w
to select “Front High/Front Wide/
Zone 2”, and
e
/
r
to select “Zone 2”.
`
Zone 2 :
Zone 2 speakers can be used (Powered Zone 2
enabled).
Setting the Zone2 Out
1
Press
Receiver
followed by
Setup
.
The main menu appears.
2
Use
q
/
w
to select “Hardware Setup”, and then
press Enter .
The “Hardware Setup” menu appears.
3
Use
q
/
w
to select “Multi Zone”, and then press
Enter .
The “ Multi Zone ” menu appears.
4
When you’ve finished, press Setup .
The setup menu closes.
Using Zone 2
1
To turn on Zone 2 and select an input source, press
Zone 2 followed by an input selector button
within 8 seconds.
Zone 2 turns on, the Zone 2 indicator lights.
To select AM or FM, press the Tuner input selector
button repeatedly.
(North American models) You can also select SIR-
IUS.
To select the same source as that of the main room,
press
Zone 2
repeatedly until “ Z2 Selector:
Source ” appears on the display.
Note
• You cannot select different AM or FM radio stations for
your main room and Zone 2. The same FM/AM radio sta-
tion will be heard in each room.
2
To turn off Zone 2, press Off .
Zone 2
Off
Zone 2 indicator Input selector buttons