Customer Services (858) 578-7887 & (888) GO IN
TEC
IN
TEC
Controls, 12700 Stowe Dr., Suite 1
0
0, Poway, CA 92064
Fax (858) 578-4633 & (888) FX IN
TEC
www.inteccontrols.com
Specification subject to change without notice.
Printed in USA 131119
Polygard® is a registered trademark of MSR
LGC/LG2-04
PolyGard
®
Multi-Point Controller
User Manual - LGC/LG2-04
Page 30
8 Notes and General Information
It is important to read user manual thoroughly and clearly understand the information and instructions. The
PolyGard
®
LGC/LG2-04 monitoring, control and alarm system must be used within product specification
capabilities. The appropriate operating and maintenance instructions and recommendations must be followed.
Due to ongoing product development, MSR reserves the right to change specifications without notice. The
information contained herein is based upon data considered to be accurate. However, no guarantee is expressed
or implied regarding the accuracy of this data.
8.1 Intended product application
The PolyGard
®
LGC/LG2-04 are designed and manufactured for control applications for energy savings and
OSHA air quality compliance in commercial buildings and manufacturing plants (i.e., detection and automatic
exhaust fan control for automotive maintenance facilities, enclosed parking garages, engine repair shops,
warehouses with forklifts, fire stations, tunnels, etc.).
8.2 Installers` responsibilities
It is the installer’s responsibility to ensure that all PolyGard
®
LGC/LG2-04 are installed in compliance with all
national and local codes and OSHA requirements. Installation should be implemented only by individuals familiar
with proper installation techniques and with codes, standards and proper safety procedures for control installations
and the latest edition of the National Electrical Code (ANSI/NFPA70). It is also essential to strictly follow all
instructions as provided in the user manual.
8.3 Maintenance
It is recommended that the PolyGard
®
LGC/LG2-04 performance check is done on a routine schedule. Any
performance deviations may be serviced based on needed requirements.
8.4 Limited warranty
MSR-Electronic-GmbH and IN
TEC
Controls warrants the PolyGard
®
LGC/LG2-04 for a period of two years,
12 months normal exposure for the sensor, from the date of shipment against defects in material or workmanship.
Should any evidence of defects in material or workmanship occur during the warranty period, IN
TEC
Controls will
repair or replace the product at their own discretion, without charge.
This warranty does not apply to units that have been altered, had attempted repair, or been subject to abuse,
accidental or otherwise. The warranty also does not apply to units in which the sensor element has been overexposed
or gas poisoned. The above warranty is in lieu of all other express warranties, obligations or liabilities.
This warranty applies only to the PolyGard
®
LGC/LG2-04. MSR-Electronic-GmbH and/or IN
TEC
Controls shall not
be liable for any incidental or consequential damages arising out of or related to the use of the PolyGard
®
LGC/
LG2-04.
If the PolyGard
®
LGC/LG2-04 needs to be returned to IN
TEC
Controls for service, an RMA number must be obtained
prior to sending.
Specifications subject to change without notice. | USA 131119 | Page 30 of 30
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
LGC-LG2 – UserManual
Polygard® is a registered trademark of MSR | LGC/LG2-04
Specifications subject to change without notice. | USA 160104 | Page 30 of 30
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC
| relevantsolutions.com/inteccontrols
LGC-LG2 – UserManual
PolyGard
®
is a registered trademark of MSR-Electronic GmbH | LGC/LG2-04
INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com
Specifications subject to change without notice. | USA 200211 | Page 30 of 30
LGC-LG2 – UserManual
