Inspiration Tecotherm Neo Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 76

background image

IfU TECOTHERM NEO TN300 EN - 01.doc

Page 66 of 76

Ref No. TN300 EN-01

11.4 Alarm Fluid level too low

see Section 11.6, too

Fluid level too low. Little or no Fluid in the container.

NOTE

When alarm is appearing push key T5 to silence audible

alarm (AUDIO paused,

is appearing at the display.)

Caused by

Leakage in the TECOTHERM NEO device / Hydraulic Module.

Lack of fluid caused by leakage in hoses, at couplings or in mattress

In the container

Fluid volume is less than 1/3 for at least 10 seconds.

There are now 8 minutes to resolve the problem.

Attention

Check immediately whether liquid is escaping or

was escaping from the device.

Check immediately whether a leakage is in the mattress or hoses.

If a big leak or fluid volume is seen below or near the device

immediately shut off

the

device. Proceed as in other alarm cases. Follow the instructions in the Main MENU.
Contact your local service.

Elimination/ Management

If  leakage  or  /  and  indication  of  escaped  liquid/  traces  of  liquid    in  your  urgent
immediate inspection was not found refill the system. For refilling TECOmed follow the
procedure of section 8.5.
Continue treatment following Main MENU instructions.
If  alarm  persists  and  symbol  is  not  disappearing  you  have  to  make  troubleshooting
more systematically.

Case 1

Check / inspection of the device

Inspect  the  support  area  below  the  device,  device  bottom  and  lower  casing  parts  for
traces and indications of liquid/ moisture.
If  you  find  a  small  or  medium  leak:    Immediately  Shut  Off  the  device  following  the
instructions in the Main MENU. Unplug mains. Contact / inform your local service.
If you find a small leak contact your service for assistance how to proceed.

«
...
64
65
66
67
68
...
»

Содержание Tecotherm Neo













































































Отзывы:

Нет отзывов

Похожие инструкции для Tecotherm Neo

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Бренд: Wacker Neuson Страницы: 62

Бренд: XM Fitness Страницы: 10

Бренд: Haaga Страницы: 31

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: XanLite Страницы: 4

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

LED Niova 150-F Pro 150W Bi Color

Бренд: Walimex Pro Страницы: 56

Бренд: Sport-thieme Страницы: 20

Бренд: ZAMST Страницы: 14

Бренд: Elliott Страницы: 46

Бренд: KUHN Страницы: 44

BoilerMag XT Series

Бренд: Spear & Jackson Страницы: 8

Бренд: MAHA Страницы: 138

Бренд: Otto Bock Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды