Unpack tap components.
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
Property Damage:
Do not pinch or break copper
tubing. Do not distort the last 25.4mm of tubing.
INSTALLING THE TAP
a
HOW TO USE THIS INSTRUCTION MANUAL
These instructions are separated into main sections, indicated by numbers, and subsections,
indicated by capital letters. The manual is setup this way to allow you to take a break at any
point after completing a section or subsection without affecting the installation process.
What you’ll see in the
instruction manual:
1
2
Equipment You May Need:
We are delighted that you have chosen the InSinkErator
®
Instant Hot Water Tap to be a part
of your home. This unique appliance will save you time and effort in the kitchen, and you’ll
enjoy discovering new uses for it each day. That’s exactly why millions of people are now
using an InSinkErator Instant Hot Water Tap.
We are confident that by following our step-by-step instructions, you’ll soon be enjoying
the convenience of instant hot water.
For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this
instant hot water tap.
This particular unit is not intended for commercial use.
Make sure that all electrical wiring and connections conform to local codes.
A standard 230-volt grounded electrical outlet is required under the sink for the tank’s electrical power.
The wall outlet powering your tank must have power supplied to it continuously.
This outlet must be fused and should not be controlled by the same wall switch that operates the disposer,
unless you have a SinkTop Switch
™
from InSinkErator
®
.
Faucet must be installed such that the outlet opening is greater than 25mm above the overflow rim of the sink.
It is recommended that a dedicated control valve be installed on the cold water line supplying water to
this system.
If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation
of this unit, it is recommended to use our water filtration system.
This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the
number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty
water discharged from the hot water tap may indicate the need for service or replacement of this product.
The use of a water filter should NOT result in the water pressure to drop below 172 kPa. If it does,
this will prevent your unit from operating properly.
Moving parts inside the tank causing a rattling noise is normal.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Equipment Required:
n
Drill
n
T-fitting
n
Dedicated control valve
n
Adjustable wrench
n
Phillips and flat blade screwdrivers
n
Pencil
n
Tape Measure / Ruler
n
Level
Anchors for drywall
Hole saw
Basin wrench
Hole punch
If you intend to use the sprayer hole in your sink for your tap, you may need a basin wrench and a
3.2mm plug or a 6.4mm cap (
not supplied
) for the faucet spray hose line.
See Step 1-B.
If you need to cut a mounting hole in your stainless steel sink, you may need a 32mm- 38mm hole
saw made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into
a surface other than stainless steel.
WHAT YOU NEED TO GET STARTED
3
2
Provides a step-by-step narrative describing the installation step, with check boxes that
can be marked as you progress through the installation.
Contains simple illustrations that provide visual instruction to support the narrative.
Important safety messages that will require your attention during the step.
1
2
3
Warning indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
Caution indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
Notice is used to address practices not related to personal injury.
NOTICE
NOTICE
NOTICE
NOTICE
3
COMPONENTS IN THIS PACKAGE
H-Classic-SS
H-Hot150
HC-View-SS
H-View-SS
H-Wave-SS
HC-Wave-SS
1/4" Tube
Brass Nut / Ferrule /
Tube Insert
Quick Connector
3/4" Screws (2)
Extension & Star Nut
*
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
Semi-Circular
Mounting Plate
1-1/4"
1-5/16"
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
1-1/4"
1-5/16"
3/4" Screws (2)
Extension & Star Nut
*
H-Contour-SS
Wing Nut
Trim Ring
Tank
Tank
3/4" Screws (2)
Semi-Circular
Mounting Plate
Flat Gasket
Tank
3/4" Screws (2)
Tank
Plastic Spacer
H-Hot100
Long Nut
Rubber Washer
H-Classic-SS
H-Hot150
HC-View-SS
H-View-SS
H-Wave-SS
HC-Wave-SS
1/4" Tube
Brass Nut / Ferrule /
Tube Insert
Quick Connector
3/4" Screws (2)
Extension & Star Nut
*
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
Semi-Circular
Mounting Plate
1-1/4"
1-5/16"
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
1-1/4"
1-5/16"
3/4" Screws (2)
Extension & Star Nut
*
H-Contour-SS
Wing Nut
Trim Ring
Tank
Tank
3/4" Screws (2)
Semi-Circular
Mounting Plate
Flat Gasket
Tank
3/4" Screws (2)
Tank
Plastic Spacer
H-Hot100
Long Nut
Rubber Washer
*component parts pre-installed on tap
32mm
32mm
H-Classic-SS
H-Hot150
HC-View-SS
H-View-SS
H-Wave-SS
HC-Wave-SS
1/4" Tube
Brass Nut / Ferrule /
Tube Insert
Quick Connector
3/4" Screws (2)
Extension & Star Nut
*
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
Semi-Circular
Mounting Plate
1-1/4"
1-5/16"
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
1-1/4"
1-5/16"
3/4" Screws (2)
Extension & Star Nut
*
H-Contour-SS
Wing Nut
Trim Ring
Tank
Tank
3/4" Screws (2)
Semi-Circular
Mounting Plate
Flat Gasket
Tank
3/4" Screws (2)
Tank
Plastic Spacer
H-Hot100
Long Nut
Rubber Washer
HC900
H-Classic-SS
H-Hot150
HC-View-SS
H-View-SS
H-Wave-SS
HC-Wave-SS
1/4" Tube
Brass Nut / Ferrule /
Tube Insert
Quick Connector
3/4" Screws (2)
Extension & Star Nut
*
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
Semi-Circular
Mounting Plate
1-1/4"
1-5/16"
Small Steel
*
Fiber
Rubber
*
Large Steel
Washers
1-1/2"
1-1/4"
1-1/4"
1-5/16"
3/4" Screws (2)
Extension & Star Nut
*
H-Contour-SS
Wing Nut
Trim Ring
Tank
Tank
3/4" Screws (2)
Semi-Circular
Mounting Plate
Flat Gasket
Tank
3/4" Screws (2)
Tank
Plastic Spacer
H-Hot100
Long Nut
Rubber Washer
33mm
38mm
