Do not pinch or break copper tubing. Do not distort the
last 1" (25mm) of tubing.
■
Unpack hot water tap components.
■
On a firm, flat surface, carefully
straighten the copper tubing.
■
For your satisfaction and safety, read all instructions, WARNINGS, CAUTIONS and NOTICES including
Important Safety Information section, before installing or using this steaming hot water tap.
■
Make sure that all electrical wiring and connections conform to local codes.
■
A standard, earth (grounded) electrical outlet is required under the sink for the tap’s electrical power.
■
The wall outlet powering your tap must have electrical power supplied to it continuously.
■
This outlet must be fused and should not be controlled by the same wall switch that operates the food waste
disposer. Fuse/circuit breaker required is 10 amp for 230 volt (10 amp for 220-240 volt UK) and 15 amp for
120 volt.
■
To ensure proper operation, this unit is not intended to be flushed with chlorine. If you suspect elevated levels
of chlorine in your water, it is recommended to use our water filtration system.
■
To prevent damage or unit not operating properly, the water pressure must be between 25 psi - 125 psi (172
kPa - 862 kPa; 1.7 bar - 8.6 bar). Ambient (room) temperature between 50ºF and 100ºF (10ºC and 38ºC).
■
Moving parts inside the tank causing a rattling noise is normal.
■
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Equipment You May Need:
Equipment Required:
■
Drill
■
Compression fitting, T-fitting
or saddle valve
■
Adjustable spanner
■
Anchors for plasterboard
■
Hole saw
■
Basin nut wrench
■
Hole punch
If you need to cut a mounting hole in the stainless steel sink, you may need a hole punch or a 1 3/8" - 1 1/2"
(35mm - 38mm) hole saw made for cutting stainless steel.
*Filtration system is optional
Hole size requirements: – H1300, C1300 hole requirement is 1 1/4
"
- 1 1/2
"
(32mm - 38mm).
Consult a professional before drilling into a surface other than stainless steel.
WHAT YOU NEED TO GET STARTED
■
Phillips and flat blade screwdrivers
■
Pencil
■
Tape Measure
■
Spirit level
2
These instructions are separated
into main sections, indicated by
numbers, and subsections,
indicated by capital letters. The
manual is set-up this way to
allow you to take a break at any
point after completing a section
or subsection without affecting
the installation process.
Provides a step-by-step narrative describing
the installation step, with tick boxes that can be
marked as you progress through the installation.
Contains simple illustrations that provide visual
instruction to support the narrative.
WARNINGS, CAUTIONS and NOTICES that will
require your attention during the step.
1
2
1
2
3
HOW TO USE THIS INSTRUCTION MANUAL
HOW TO USE THIS INSTRUCTION MANUAL
3
A potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Potentially hazardous situation which, if not avoided, could result in minor
or moderate injury.
Notice is used to address practices not related to personal injury.
NOTICE
NOTICE
3
Filter Head & Cartridge
(optional)
3/8" (9.5mm) White Tubes (2)
3/4" (19mm) Screws (4)
Y-Quick Connector
Semicircular
Mounting Plate
Rubber O-Ring
Hex Nut
Hex Tool
HWTank
Plug (1)
H1300
C1300
Brass Nut / Ferrule /
Tube Insert
A
OVERVIEW OF A COMPLETED SET-UP
Do not plug in the hot water tank until step 7B. To avoid permanent damage to the product,
only operate the tank after it is filled with water.
NOTICE
PREPARATION
START HERE
PROPER INSTALLATION SHOULD TAKE ABOUT 2-4 HOURS
■
Identify locations for the tap, tank and
filter (if applicable).
■
Check to make sure there is proper
clearance (see chart at left) for tap
handle to be fully opened.
■
Check to make sure counter is not too
thick (see chart at left).
■
Make sure there is an earth (grounded)
electrical outlet under the sink.
■
Turn off water supply.
1
The wall outlet for the tap must have power
supplied to it continuously and must be fused.
It should not be controlled by the same wall
switch that operates the food waste disposer.
If you have to drill through sink or
worktop, you may need to rent or
purchase the appropriate tools.
Required minimum from center of hole to wall
Maximum counter thickness is 3
"
(76mm).
Property Damage:
Do not pinch or break copper tubing.
Do not distort the last 1" (25mm) of tubing.
■
Unpack hot water tap components.
■
On a firm, flat surface, carefully
straighten the copper tubing.
■
Ensure that the black O-ring is properly
seated in the base of the tap head (the
groove on the underside of the tap).
INSTALLING THE TAP
2
■
Feed tubes down through the hole
in the sink or countertop until the base
is at rest.
■
From under the sink, place the
semi-circular mounting plate and hex
nut onto the threaded stud. Ensure tap
head is at desired angle.
■
Insert screwdriver into hole on side of
hex tool (creating a “T”), and use tool
to tighten nut and secure tap.
An assistant may be needed to hold
the tap in place while securing.
H1300..............................3 1/4" (83mm)
C1300..............................3 1/4" (83mm)
NOTICE
A
A
B
B
IN THIS PACKAGE
*