INSIGHT Vital Signs Plus ECG Скачать руководство пользователя страница 42

Страница: 42 / 58

Physiological Alarm

Notification

Reason

SpO2 too high

SpO2 measured is higher than the upper alarm limit

SpO2 too low

SpO2 measured is below the lower alarm limit

PR too high

PR measured is higher than the upper alarm limit

PR too low

PR measured is below the lower alarm limit

Technical Alarm

Notification

Reason

Solution

System

Error3/SysErr3

Self-test failure of blood

oxygen module

Contact Woodley Equipment

Company.

System

Erro4/SysErr4

Blood

oxygen

module

communication error

Contact Woodley Equipment

Company.

No Sensor

Sensor not connected

Make sure that the sensor is

placed on the animal's tongue

or ear and that the monitor is

connected

the

cable

properly.

Sensor off

Sensor switched off

Tips (including general warnings)

Notification

Reason

No pulse

No pulse was found

Searching

Searching for a pulse

7.5 Maintenance and Cleaning

Warning

Before cleaning the monitor or sensor, turn off the power and disconnect the AC

power.

Warning

Do not autoclave the sensor.

Do not immerse the sensor in liquid,

If the sensor or cable has signs of damage or deterioration, it is forbidden to use

again.

Cleaning:

The surface of the sensor can be wiped with cotton ball or soft cloth dipped with

medical alcohol, and then dried with dry cloth. The light emitting tube and the

receiver part of the sensor can be cleaned in the same way.

The cable can be cleaned and disinfected with 3% hydrogen peroxide or 70%

isopropanol. The connector cannot be immersed in the above solution.

Содержание Vital Signs Plus ECG



























































Результаты поиска

Содержание Vital Signs Plus ECG

Отзывы:

Похожие инструкции для Vital Signs Plus ECG

Бренды по названию

Популярные бренды

INSIGHT Vital Signs Plus ECG, Руководство оператора

Результаты поиска

Содержание Vital Signs Plus ECG

Отзывы:

Похожие инструкции для Vital Signs Plus ECG

Бренды по названию

Популярные бренды