Page | 6
Product Description
LPS2802-T1 Series Outdoor Industrial PoE Switch features with eight PoE Ethernet ports and comply to
10/100/1000BaseT(X), IEEE802.3af/at PoE and two Gigabit SFP fiber optics uplink interfaces. Each of the
PoE ports supplies DC power up to 15.4W for 802.3af, 25.5W for 802.3at, and 30W for 802.3at Plus. The
system is integrated with a 200W DC power supply. The transfer data is up to 120Km from SFP fiber port
to a control center. Additionally, the product also features with an anti-electromagnetic interference
designed for harsh outdoor applications, and the 3KV network port surge protection adapts to harsh
outdoor environment and ensures the reliability of the uninterrupted PoE operations. The system is
rated at IP68, and the system is able to operate under -30
˚
~ +70
˚ C
temperature range.
Product Features
1.
The system supports
DUAL POWER INPUT REDUNDANCY
2.
Comply to IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.3ab, IEEE 802.3x, IEEE 802.1D, IEEE
802.3at, IEEE 802.3af, IEEE 802.1Q IEEE 802.1p, IEEE 802.1x, IEEE 802.1W, SNMP, IGMP
standards
3.
Eight 10/ 100/ 1000M self-sensing RJ45 port, support PoE power supply function; All ports
support auto-flip (Auto MDI/MDIX);
4.
Each PoE port can provide power up to 15.4W p er IEE E802.3af standard;
5.
Support IEEE802.3x full duplex flow control and duplex backpressure flow control;
6.
8.8G backplane bandwidth;
7.
1K MAC address table;
8.
Its 3KV network port surge protection can adapt to harsh outdoor environment; Under the
temperature of -30
˚
~ +70
˚
C, working at a full load 144W for IEEE802.3af with the internal
power supply;
9.
The four gigabit SFP fiber ports are capable of high bandwidth and for up to 120KM long
distance transmission.
10.
Dual redundancy power input, AC and DC
, (More than 50V DC recommended when used PoE+
output)
Installation
a.
Before installation, please ensure the following:
1)
All PD devices, i.e., PoE Clients, meet the power requirement of the connecting devices.
2)
All PD devices, i.e., PoE Clients, match with the power receiving device power pinout
specification (1/2+ & 3/6-)
b.
Connect the power cable to a power source, 110 ~ 240V AC, the 48V DC is optional and can be
used as the backup power or primary power when the AC power is not available. Then the
switch will automatically initialize, and LED lights status will display as following:
i.
Except the POE port lights, all the other lights will go through the process of “on
-off-on-
off”, which means the installation is successful.
ii.
Power LED remains ON
c.
Connect the network devices with network cables to the POE switch port though the waterproof
connectors, then secure the Top Cover with the four screws to the Bottom Case
d.
After the Ethernet and/or fiber optics network devices are connected, please refer the LED
Indicator Description Table Below on Page 6
e.
With the dual redundancy power input, you can connect a DC power source with the 4-Pin
DC Connector to the DC Input Connector simultaneously with the AC Input. When
connected, the DC Input operates as a backup power.
f.
Lastly, to avoid hardware damage due to transient voltage from lightning and thunderstorm,
PLEASE MAKE SURE YOU CONNECT THE GROUNDING WIRE TO EARTH GROUND, E.G., GROUND
ROD (see Page 9 for details).
