Innovative EBB & FLOW Скачать руководство пользователя страница 6

Страница: 6 / 18

EBB & FLOW BENCH ASSEMBLY INSTRUCTIONS

STEP #5

Now stand up the leg support on the opposite end of the frame and a

ach the clamps on

each corner on that side as well. Then stand up any leg supports in the middle of the
frame and repeat the steps again un

l the frame is complete (shown on Figure 4a & 4b).

NOTE: Longer tables will require addi

onal leg supports in the middle of the frame so just use the

diagrams a

ached for reference. They will provide spacing requirements

STEP #6

Once the legs are all standing, you
can insert the load bearing plugs
(A4) into the bo

om of all the

welded legs.

(B1 – see Figure 5)

Also, install them to the ends of the
stringer pipes on each corner of the
frame

(shown on Figure 6).

INNOVATIVEGROWERSEQUIPMENT.COM

Call 815-991-5010 or email us at sales@innova

vegrowersequipment.com if you have any ques

ons

FOLLOW INSTRUCTIONS BELOW

CONT.

FIGUIRE 4a

FIGUIRE 4b

STRINGER PIPE

UNATTACHED

LEG SUPPORT

ATTACH ALL REMAINING

LEG SUPPORTS TO THE

FRAME

FIGUIRE 5

FIGUIRE 6

Содержание EBB & FLOW



















Результаты поиска

Содержание EBB & FLOW

Отзывы:

Похожие инструкции для EBB & FLOW

Бренды по названию

Популярные бренды

Innovative EBB & FLOW, Руководство по сборке

Результаты поиска

Содержание EBB & FLOW

Отзывы:

Похожие инструкции для EBB & FLOW

Бренды по названию

Популярные бренды