Innovatech Predator 2400 Скачать руководство пользователя

Страница: 9 / 61

Predator 2400

Owner’s Manual

OIPB-

IO-2003-P2400 GRINDER

9 |

P a g e 0 1 / 1 7 / 2 0 1 9

OPERATION INSTRUCTIONS

Before starting:

Check the floor carefully and remove all bolts, nails, as well as any loose material that
could get caught in the machine.

Fit the appropriate tools to the machine.

Fit splash guard to the right height.

Connect the power supply. Make sure you have all the phases. May have to check with
volt meter.

If you are grinding dry, connect the appropriate vacuum and start vacuum before
starting the grinder.

Starting machine:

Turn main power switch on side of power box to ON.

Turn forward or reverse switch left of right.

Turn manual speed pot up to get the heads turning for desired speed. (If heads do not
move, you may have to lean on handle to reduce pressure on tools.

Always grip handle firmly when starting machine. The machine will always move from
side to side with first start.

When finished with grinding, turn off machine and let the heads come to a complete
stop before tilting back the machine.

Changing of Tools:

Before working on the grinder, bring the motor to a total stop and disconnect power.

Tilt machine back on floor.

Use caution! Tools can be very hot from grinding. Use gloves.

Use special tool supplied to turn center of tool holder to remove tool plate.

Replace with new tool plate and turn to lock in place.

Lower machine back down and re-adjust splash guard is necessary.

NOTE: IF THE WRONG POWER IS SUPPLIED TO THE GRINDER, IT WILL DAMAGE
THE ELECTRICAL COMPONENTS IN THE INVERTERS.

Содержание Predator 2400






























































Результаты поиска

Содержание Predator 2400

Отзывы:

Похожие инструкции для Predator 2400

Бренды по названию

Популярные бренды

Innovatech Predator 2400, Руководство пользователя

Результаты поиска

Содержание Predator 2400

Отзывы:

Похожие инструкции для Predator 2400

Бренды по названию

Популярные бренды