Innovatech Predator 2400 Скачать руководство пользователя

Страница: 12 / 61

Predator 2400

Owner’s Manual

OIPB-

IO-2003-P2400 GRINDER

12 |

P a g e 0 1 / 1 7 / 2 0 1 9

•

Motor power rating too low for the
application

O P F
Motor phase failure

•

Loss of phase at drive controller
output

•

Downstream contractor open

•

Motor not connected

•

Instability in the motor current

•

Drive controller oversized for motor

•

Check the connections from the drive
controller to the motor

•

Test the drive controller on a low power
motor or without a motor: set OPL to nO

O S F
Over voltage during
steady state
operation or during
acceleration

•

Line voltage too high

•

Line supply transients

•

Check the line voltage. Compare with the
drive controller nameplate rating

•

Reset the drive controller

P H F
Input phase failure

•

Input phase loss, blown fuse

•

Three-phase drive controller used
on a single-phase line supply

•

Input phase imbalance

•

Transient phase fault

NOTE: This protection only operates
with the drive controller running
under load

•

Check the connections and the fuses

•

Verify that the input power is correct

•

Supply three-phase power if needed

C F F
Configuration Fault

•

The parameter configurations are
not suited to the application

•

Restore the factory settings or load the
backup configuration, if it is valid

U S F
Under Voltage

•

Line supply too low

•

Transient voltage dip

•

Damaged precharge resistor

•

Check the line voltage

•

Replace the drive controller

Содержание Predator 2400






























































Результаты поиска

Содержание Predator 2400

Отзывы:

Похожие инструкции для Predator 2400

Бренды по названию

Популярные бренды

Innovatech Predator 2400, Руководство пользователя

Результаты поиска

Содержание Predator 2400

Отзывы:

Похожие инструкции для Predator 2400

Бренды по названию

Популярные бренды