Innovate Motorsports MTX-D Скачать руководство пользователя страница 12

Appendix A:  Limited Warranty 

 

LIMITED WARRANTY

 

Innovate stands behind the quality of its products. Innovate makes the following warranty to 
purchasers of its products: All new Innovate products carry a one year warranty from the date of 
purchase. If proof of purchase cannot be provided, warranty will be determined by date of 
manufacture. 

When Warranty Void

 

This warranty shall terminate and Innovate shall have no obligation pursuant to it if (i) your 
Innovate product has been modified or repaired in a manner not previously authorized by 
Innovate in writing, (ii) the identification markings on your Innovate product have been removed, 
defaced, or altered; (iii) your Innovate product was subjected to accident, abuse, shipping 
damage, or improper use; (iv) your Innovate product was not used or configured as specified in 
the product manual; or (v) your Innovate product was subjected to operating conditions more 
severe than those specified in the product manual. 

Exclusions From This Warranty

 

Oxygen Sensors are excluded from this warranty. 

Repairs Under This Warranty

 

In the unlikely event that your Innovate hardware product should prove defective during the 
warranty period, contact Innovate Customer Support for a return material authorization (RMA) at 
(800) 348 3037. Products returned for service must be securely packed to prevent damage and 
shipped charges pre paid, along with proof of purchase and the return material authorization 
form, to the Innovate repair location as instructed by Customer Service. Innovate within a 
reasonable amount of time from its receipt of your product so shipped, will ship to you, at its 
option, the repaired product or a new or reconditioned product of comparable or greater 
specified functionality. All repaired or replacement products shall be warranted for the remainder 
of the original product warranty.  

Disclaimer

 

INNOVATE MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO 
YOUR INNOVATE PRODUCT OTHER THAN THE LIMITED WARRANTY SET FORTH 
ABOVE. No Innovate dealer, agent, or employee is authorized to make any modification, 
extension, or addition to this warranty, unless enforceable or unlawful under applicable law, 
INNOVATE DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED 
WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A 
PARTICULAR PURPOSE, AND THE LIABILITY OF INNOVATE, IF ANY, FOR DAMAGES 
RELATING TO ANY ALLEGEDLY DEFECTIVE PRODUCT SHALL UNDER ANY TORT, 
CONTRACT, OR OTHER LEGAL THEORY BE LIMITED TO THE ACTUAL PRICE PAID FOR 
SUCH PRODUCT AND SHALL IN NO EVENT INCLUDE INCIDENTAL, CONSEQUENTIAL, 
SPECIAL, OR INDIRECT DAMAGES OF ANY KIND EVEN IF INNOVATE IS AWARE OF THE 
POSSIBILITY OF SUCH DAMAGES. Some states do not allow limitations on how long an 
implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so 
the above limitations or exclusions may not apply to you. 

 

 

 

 

Содержание MTX-D













Отзывы: