background image

 

Operating Manual  

      IP Telephone IP200 

                   - 37 -

- 37 -

 

 

Safety instructions 

The manufacturer assumes no responsibility for any personal injury, damage to property 
or subsequent damage that can be attributed to improper use of the device. 

innovaphone® AG declares that the device meets all basic requirements of the 
1999/5/EC European guideline. 

The innovaphone Wiki at wiki.innovaphone.com should also be observed for 
configuration of the IP telephones. All instructions specified there should be followed 
carefully and the devices should only be used in accordance with these instructions. 

 

¾

 Power supply 

 

The external power supply is designed for operation with a 100-240 V, 50 Hz AC mains 
network. Never try to connect the equipment to other mains systems! 

The equipment cannot be operated during a mains failure. The equipment settings 
however are retained. 

The power socket must be near to the equipment and easy to access. The power 
supply to the device can be interrupted by pulling the mains adapters out of the power 
socket or, if the power is supplied via a network cable (Power over LAN), by removing 
the network cable. 

¾

 Installation and connection 

 

Lay the connection cables carefully so that no one can trip over them. Connected 
cables must not be bent excessively, pulled or subjected to mechanical strain. 

The equipment is intended for use in dry rooms only. 

The equipment must not be installed and operated under the following conditions: 

Some types of furniture varnish or cleaning products can damage the plastic feet of the   
telephone IP200 and leave marks. In these cases, make sure you put the equipment on 
a stable, non-slip surface. 

 

Note: 
Please note the following instructions for your own safety: 

 

In damp, dusty rooms or in rooms where an explosion may occur 

 

At temperatures over 40°C or under 0°C 

 

Where it is subject to impact stress or vibrations 

 

At places subject to direct sunlight 

Содержание IP200









































Отзывы: