Innotech Vaisala WMT Скачать руководство пользователя

Страница: 21 / 24

Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor

Page 21

Edition 6.0 dated 04/01/2017

Services Tab

Under the Service tab you can configure or modify the following settings:

•

Maintenance Mode – used for service by Innotech personnel.

•

Server IP Address – only used when Maintenance Mode is set to Server or Client.

•

Server Port – only used when Maintenance Mode is set to Server or Client.

•

Reboot Gateway Now – Reboot the IG04 BACnet Gateway

Figure 19:

Configure IG04 settings in FusionLIVE – Service Tab

The Maintenance mode is a service tool for Innotech personnel only. It MUST be set to

Normal

in order to view the

data from the Vaisala device, unless instructed otherwise, as illustrated in Figure 19 below.

Содержание Vaisala WMT

























Результаты поиска

Содержание Vaisala WMT

Отзывы:

Похожие инструкции для Vaisala WMT

Бренды по названию

Популярные бренды

Innotech Vaisala WMT, Руководство по установке

Результаты поиска

Содержание Vaisala WMT

Отзывы:

Похожие инструкции для Vaisala WMT

Бренды по названию

Популярные бренды