Ingersoll-Rand RO2 B Series, Информация по обслуживанию

Страница: 2 / 4

2 16575011_ed2
WARNING
Always wear eye protection when operating or performing maintenance on this tool.
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool or
before performing any maintenance on this tool.
Note:
When reading the instructions, refer to exploded diagrams in parts Information Manuals when applicable (see under Related Documentation
for form numbers).
Disassembly
General Instructions
Never apply excessive pressure by a holding device which may
cause distortion of a part.
Apply pressure evenly to parts, which have a press fit.
Apply even pressure to the bearing race that will be press fitted
to the mating part.
Use correct tools and fixtures when servicing this tool.
Don’t damage “O” Rings when servicing this tool.
Use only genuine
Ingersoll Rand
replacement parts for this tool.
When ordering, specify part number, description, tool model
number and serial number.
Disassembly of Motor
Remove Sanding Pad (34).
Remove Lock Ring (27) and pull Motor and Seal (22) from Housing.
Remove Retaining Ring (18).
Using special brass blocks to fit around outside diameter
of Cylinder, clamp around Cylinder and press Shaft of
Counterbalance through Bearing (19) and End Plate (20).
Remove Blades (24), Rotor (23), and Key (28).
Remove End Plate (25) and Bearing (19).
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
Vacuum Adapter Removal
25 mm size: While pressing in on the tabs on the side, pull
vacuum adapter out.w
To remove the 28 and 32 mm size:
Remove muffler and pull
vacuum adapter out.
Throttle Disassembly
Remove Vacuum Adapter (15).
Remove Inlet Adapter (13), releasing Spring (12) & Valve (11).
Note: Do not remove seat (10) unless damage is evident.
Remove Muffler (14).
To remove Valve Stem (6), remove Roll Pin (8) and Lever (7).
Regulator Disassembly
Remove Lever (7) by removing Roll Pin (8).
Remove Snap Ring (5) from Regulator (3).
Remove regulator assembly (3) - includes 2 “O” Rings (4).
1.
2.
1.
2.
3.
4.
1.
2.
3.
Assembly
Assembly of Motor
Grease and assemble “O” Ring (26) to Lock Ring (27).
Assemble Lock Ring over Counterbalance (29).
Assemble Bearing (19) into End Plate (25), pressing on outer race
of Bearing.
Assemble End Plate (25) onto Shaft of Counterbalance, pressing
on inner race of Bearing.
Install Key (28) in key slot.
Assemble Rotor (23) to Counterbalance, aligning key-way to
Key (28).
Assemble Five rotor blades (24) to Rotor Slots.
Assemble Cylinder (21) over Rotor, aligning Roll Pin in Cylinder
with slot in End Plate.
Assemble Bearing (19) into End Plate (20), pressing on outer race
of Bearing.
Assemble End Plate (20), with Bearing (19), to Counterbalance,
pressing on inner race of Bearing.
Note: Align slot in End Plate with Roll Pin in Cylinder.
Install Retaining Ring (18) to groove in Counterbalance, with bow
in ring positioned as shown in parts illustration page.
Assemble Seal (22) to grooves in Cylinder.
Assemble Motor to Housing, aligning Seal (22) with air inlet.
Tighten Lock Ring (27), securing Motor Assembly.
Assemble Sanding Pad (34) and tighten securely.
Throttle Assembly
Coat Valve Stem (6) with
Ingersoll Rand
29665 spindle oil and
assemble into Housing with hole in Valve Stem in line with
Housing to accept Valve (11).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
1.
Assemble Seat (10) into Housing with rounded corners into
housing first.
Coat Valve (11) with
Ingersoll Rand
29665 spindle oil and
assemble into housing, securing Valve Stem (6).
Assemble Spring (12) into Housing.
Assemble Inlet Adapter (13) to Housing, securing throttle
components.
Assemble Lever (7) to Housing, securing with Roll Pin (8).
Assemble Vacuum Adapter (15) or Plug (16) to Housing.
Vacuum Adapter installation
25 mm size: Push into housing until tabs on Vacuum Adapter
snap into Housing.
To install 28 and 32 mm size : Remove muffler. Push adapter into
housing and align ring on vacuum adapter with exhaust. Push
muffler through ring on vacuum adapter and screw muffler to
housing.
Regulator Assembly
Assemble Regulator (3) and 2 “O” Rings (4).
Insert Regulator assembly (3) into Housing (1).
Assemble Snap-Ring (5) into groove on regulator assembly (3).
Install Lever (7) by adding Roll Pin (8).
2.
3.
4.
5.
6.
7.
1.
2.
1.
2.
3.
4.
Related Documentation
For additional information refer to:
Product Safety Information Manual 04580387.
Product Information Manual 04578399.
Parts Information Manual 16573933.
Manuals can be downloaded from www.irtools.com