background image

6

04585147_ed2

„

Load Chain

CAUTION

• Only use original chains.
• Welded seam of the chain links must face inward on 
the chain wheel (see figure 4).
• The geared limit switch must be mechanically 
disabled in order to install in the chain, see section on 
“Limit Switch”.

(Figure 4)

Before start-up and during its operation the load chain must 
be oiled along its full length. The internal, contacting and 
rubbing surfaces of the chain links must have constant oil. 
Oiling can be effected by submersion or with an oil can, 
using a creeping gear oil.
The end of the chain is to be affixed with a flexible piece of 
wire and fed through the chain wheel (1) of the electric chain 
hoist. Through short switching impulses, the chain (2) will be 
housed correctly in accordance with figure 4.
The lifting height must be dimensioned such that the hook 
fittings are on the ground in the lowest hook position.

Single fall operation: 

The connection between the load 

hook (2) and the chain is made with the hook block 
assembly (1). The last link must locate on the pin (3). Apply 
grease in the hook block recess (see figure 5).

(Figure 5)

NOTICE

• Pay attention to correct arrangement of suspension! 
(see figure 7).

Double fall operation:

 Connect load side of chain end to 

chain retainer and fix in housing guide rail (3). Bottom 
sheave (1) with load hook (2). Apply grease in the hook 
block recess (see figure 6).

(Figure 6)

NOTICE

• Pay attention to correct arrangement of suspension! 
(see figure 7). There must be no longitudinal chain 
twisting. The chain end must be attached to the housing 
in accordance with figure 6.

(Figure 7)

1

2

1

2

3

3

2

1

... kg 

... kg 

1 1/2 inch (38 mm)

1 7/8 inch (48 mm)

Содержание QCH100-1HD50













Отзывы: