Ingersoll-Rand FA150KGi Series, Информация о продукте

Страница: 10 / 16

NOTICE
• Always drain oil into a suitable container and inspect drained oil for evidence
of damage, metal shavings, dirt, water, etc. Dispose of oil in an
environmentally safe manner.
3. Collect drained oil and dispose of properly. Reinstall the reduction gear carrier
plugs.
To Fill:
1. Rotate winch drum to align reduction gear plugs to the fill position. Fill plug
position is at top center.
2. Remove fill plug located on housing.
3. Fill slowly with recommended oil, refer to Table 10 ‘Reduction Gear and Disc Brake
Capacities’ on page 9.
4. Reinstall plug.
CAUTION
• Do not overfill. Excess oil will reduce operating efficiency and increase oil
temperature.
• The use of unsuitable oil may result in excessive temperature rise, loss of
efficiency and possible damage to the gears. Use only high quality rust and
oxidation inhibiting lubricant.
n
Disc Brake Fill/Drain Procedures
Refer to Dwg. MHP2297 on page 13 and MHP3152.
Disc Brake Drain:
1. Remove drain and level plugs.
2. Collect drained oil and dispose of properly.
Disc Brake Fill:
1. Install drain plug.
2. Remove level plug.
3. Add oil slowly until oil is level with level plug port.
4. Install level plug.
n
Air Line Lubricator
An air line lubricator should be installed in air supply line as close as possible to
motor inlet, but no more than 10 ft (3 m) away. Use ISO VG 46 (SAE 10W) oil in
lubricator. Adjust lubricator to provide 6 to 9 drops per minute at maximum motor
speed.
n Wire Rope
Follow wire rope manufacturer’s instructions. At a minimum, observe the following
guidelines.
1. Clean with a brush or steam to remove dirt, rock dust or other foreign material
on wire rope surface.
CAUTION
• Do not use an acid-based solvent. Only use cleaning fluids specified by the
wire rope manufacturer.
2. Apply a wire rope lubricant.
3. Brush, drip or spray lubricant weekly, or more frequently, depending on severity
of service.
n
Seals and Bearings
If product is disassembled, clean all parts thoroughly and replace bearings and seals.
Refer to ‘Recommended Lubricants’ section on page 9. Use sufficient grease to provide
a good protective coat.
WARRANTY
Ingersoll Rand Limited Warranty
Ingersoll Rand Company (“ IR ”) warrants to the original user its material handling
products (“Products”) to be free of defects in material and workmanship for a period
of one year from the date of purchase. IR will, at its option either (1) repair, without
cost, any Product found to be defective, including parts and labor charges, or (2)
replace such Products or refund the purchase price, less a reasonable allowance for
depreciation, in exchange for the Product. Repairs or replacements are warranted for
the remainder of the original warranty.
If any Product proves defective within its original one-year warranty period, it should
be returned to any Authorized Product Service Distributor, transportation prepaid with
proof of purchase or warranty card. This warranty does not apply to Products which
IR has determined to have been misused or abused, improperly maintained by the
user, or where the malfunction or defect can be attributed to the use of non-genuine
IR repair parts.
IR MAKES NO OTHER WARRANTY, CONDITION OR REPRESENTATION OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, STATUTORY OR OTHERWISE, AND ALL
IMPLIED WARRANTIES AND CONDITIONS RELATING TO MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED.
IR
's maximum liability is limited to the purchase price of the Product and in no event
shall IR be liable for any consequential, indirect incidental or special damages of any
nature arising from the sale or use of the Product, whether in contract, tort or
otherwise.
Note: Some states do not allow limitations on incidental or consequential damages,
so that the above limitations may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which may vary from state to state.
Fulcrum series electric winch, product code 405-002: 2 year warranty.
Winch and Hoist Solutions Extended Warranty This option provides a price for
extending the Ingersoll Rand Winch and Hoist Solutions Warranty from the standard
one (1) year to two (2) years from the date of purchase. All other provisions of the
standard warranty to remain in effect.
For additional information or quotations for warranties falling outside of these
parameters, please contact your Client Services Representative with your
requirements.
10 Form MHD56470 Edition 4