manualshive.com logo in svg

Ingersoll-Rand 6WRSL3, Руководство пользователя

Поделиться
Скачать
Ingersoll-Rand 6WRSL3 Скачать руководство пользователя страница 34

34

MAINTENANCE SECTION

TROUBLESHOOTING GUIDE

Trouble

Probable Cause

Solution

Low power or low free speed

Low air pressure

Check the air pressure at the inlet.  The pressure
must not exceed 90 psig (6.2 bar/620 kPa).

Plugged Inlet Bushing Screen or
Air Strainer Screen

Clean the Screen in a clean, suitable, cleaning
solution. If it cannot be cleaned, replace it.

Worn or broken Vanes

Replace the complete set of Vanes.

Loose Rotor Bearing Retaining
Nut

Tighten the Nut.

Worn or broken Cylinder

Replace the Cylinder if it is worn or broken or if
the bore is scored or wavy.

Scoring of End Plates

Replace End Plates if they are scored.

Improper lubrication or dirt
build–up in the motor.

Lubricate the Wrench as instructed in 
LUBRICATION. If lubrication does not result in
satisfactory operation, disassemble the motor in-
spect and clean all parts.

Scoring

Improper assembly

Make certain that all motor or Cylinder parts are
properly aligned prior to clamping the motor
assembly.

Gear Case gets hot

Excessive grease

Clean and inspect the Gear Case gearing parts and
lubricate as instructed in LUBRICATION.

Worn or damaged parts

Clean and inspect the Gear Case and gearing.
Replace worn or broken components.

Tool fails to shut off

Dirt or Burrs on Shutoff Valve or
Bushing

Clean the parts and remove the burrs.

Bleeder ports plugged

Clean the bleeder ports with a fine wire.

Leaky Throttle Valve

Worn Throttle Valve and/or
Throttle Valve Seat

Install a new Throttle Valve and/or a Throttle
Valve Seat

Dirt accumulation on Throttle
Valve and/or Throttle Valve Seat

Pour about 3 cc of a clean, suitable, cleaning solu-
tion in the air inlet and operate the tool for about
30 seconds.  Immediately, pour 3 cc of the recom-
mended oil in the air inlet and operate the tool for
30 seconds to lubricate all cleaned parts.

SAVE THESE INSTRUCTIONS.  DO NOT DESTROY.

Содержание 6WRSL3




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды