This heater must be permanently installed and hard wired by a licensed electrician in accordance with local
electrical codes. Assembly procedure must be performed with no electrical power to unit.
Step 1: Check UL/CUL/CE label on heater for proper voltage.
Step 2: Follow supplied wiring instructions. (See wiring instructions below)
Step 3: Heater must be mounted with reflector angled down.
Step 4: All electrical connections must be in compliance with the National Electric Code (NEC) and local codes for
outdoor wiring.
Step 5: Use only wiring components UL/CUL/CE listed for outdoor use with IPX4 minimum rating.
INSTALLATION INSTRUCTIONS
WIRING INSTRUCTIONS
Connect power with flexible
conduit or appropriate cord
to allow heater to be swiveled
.
The heater is drilled and threaded for standard ½” conduit fittings. The installing electrician will need to provide
the appropriate rigid metallic, flexible or liquid tight conduit for the installation.
•
Use only copper or aluminum wire
suitable for 90°C.
•
Observe local electrical code regulations.
“T” SLOT
Logo Plate designed
to rotate (if required
)
If rotation is required, push in the
spring pin located on back side of
heater trim to disengage the two
pins from their alignment hole and
rotate 180°
Allows the mounting bracket to
slide for flexible mounting options
.
3
Logo Plate designed
to rotate (if required)
If rotation is required, push in the
spring pin located on back side of
heater trim to disengage the two
pins from their alignment hole and
rotate 180°
This heater must be permanently installed and hard wired by a licensed electrician in accordance with local
electrical codes. Assembly procedure must be performed with no electrical power to unit.
Step 1: Check UL/CUL/CE label on heater for proper voltage.
Step 2: Follow supplied wiring instructions. (See wiring instructions below)
Step 3: Heater must be mounted with reflector angled down.
Step 4: All electrical connections must be in compliance with the National Electric Code (NEC) and local codes for
outdoor wiring.
Step 5: Use only wiring components UL/CUL/CE listed for outdoor use with IPX4 minimum rating.
INSTALLATION INSTRUCTIONS
WIRING INSTRUCTIONS
Connect power with flexible
conduit or appropriate cord
to allow heater to be swiveled
.
The heater is drilled and threaded for standard ½” conduit fittings. The installing electrician will need to provide
the appropriate rigid metallic, flexible or liquid tight conduit for the installation.
•
Use only copper or aluminum wire
suitable for 90°C.
•
Observe local electrical code regulations.
“T” SLOT
Logo Plate designed
to rotate (if required
)
If rotation is required, push in the
spring pin located on back side of
heater trim to disengage the two
pins from their alignment hole and
rotate 180°
Allows the mounting bracket to
slide for flexible mounting options
.
3
This heater must be permanently installed and hard wired by a licensed electrician in accordance with local
electrical codes. Assembly procedure must be performed with no electrical power to unit.
Step 1: Check UL/CUL/CE label on heater for proper voltage.
Step 2: Follow supplied wiring instructions. (See wiring instructions below)
Step 3: Heater must be mounted with reflector angled down.
Step 4: All electrical connections must be in compliance with the National Electric Code (NEC) and local codes for
outdoor wiring.
Step 5: Use only wiring components UL/CUL/CE listed for outdoor use with IPX4 minimum rating.
INSTALLATION INSTRUCTIONS
WIRING INSTRUCTIONS
Connect power with flexible
conduit or appropriate cord
to allow heater to be swiveled
.
The heater is drilled and threaded for standard ½” conduit fittings. The installing electrician will need to provide
the appropriate rigid metallic, flexible or liquid tight conduit for the installation.
•
Use only copper or aluminum wire
suitable for 90°C.
•
Observe local electrical code regulations.
“T” SLOT
Logo Plate designed
to rotate (if required
)
If rotation is required, push in the
spring pin located on back side of
heater trim to disengage the two
pins from their alignment hole and
rotate 180°
Allows the mounting bracket to
slide for flexible mounting options
.
3
alfresco-heating.com
888-Warm-Glo
