manualshive.com logo in svg

Infranet Technologies M2M CONTROL CX320, Техническое руководство

Поделиться
Скачать
Infranet Technologies M2M CONTROL CX320 Скачать руководство пользователя страница 33

 M2M Control CX320  Technical Manual V1.01

 

 

 

 

Page 33 of 42 

 

LTE Worldwide Cat. 4 Cellular Engine 

The M2M Control CX320 uses an LTE/UMTS/HSPA engine with the following features: 

•

 

Max. 150Mbps down / 50Mbps upload (Cat 4) 

•

 

LTE-FDD: B1/ B2/ B3/ B4/ B5/ B7/ B8/ B12/ B13/ B18/ B19/ B20/ B25/ B26/ B28. 

•

 

LTE-TDD: B38/ B39/ B40/ B41 

•

 

WCDMA: B1/ B2/ B4/ B5/ B6/ B8/ B19 

•

 

GSM: 850/900/1800/1900 MHz 

•

 

SMS (Text and PDU) 

•

 

UMTS release 7, max. 42Mbps down / 5.76Mbps upload, (Cat 6) 

•

 

Digitized audio / DTMF capability. 

 

The Cellular Engine is designed for Worldwide deployment. 

 

SIM-Card 

The M2M Control CX320 device contains a standard Mini SIM card reader located inside the device. 
The SIM card reader is a lid-based reader with a mechanical lock system to secure the SIM card 
installation. Please refer to Appendix A for the SIM card installation guide. 

If the SIM-card is removed during the cellular operation, the device will be rejected from the network 
shortly after.   

 

Antennas 

Cellular Antenna 

The M2M Control CX320 device contains an SMA female connector for connecting a suitable LTE 
compliant antenna. When installing the antenna, please ensure that the antenna is not in close 
proximity to metallic parts or anything else, which can influence the antenna's efficiency.  
Please consult the installation guide that follows the antenna. 

Wireless M-Bus Antenna (optional) 

The M2M Control CX320 device contains an SMB male connector for connecting a suitable Wireless 
M-Bus (868 MHz) compliant antenna. 
 
 

SD-CARD reader 

The M2M Control CX320 device has a standard SD-card reader located on the device's top side (see 
the graphical overview).  The M2M Control CX320 supports a FAT file system for standard PC 
compatibility. In addition, SDHC cards with up to 32 GB capacity is supported. 

Содержание M2M CONTROL CX320











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды