Inforesight SALPHA10240 Скачать руководство пользователя страница 4

Before using this appliance: 

 

1.      Check  that  the  voltage  indicated  on  the  units  rating  label  corresponds  to  the  mains     
         supply voltage. 

 

2.

Do not install the heaters less than the minimum height from the floor as specified below 
in the specification - Table. 1. 

 

3.      Ensure that the heater has been securely fastened in its final mounting position. 

 

4.     

WARNING 

- This appliance must be grounded! 

 

5.     

WARNING 

- Keep the mains  cord away from the body of the heater  which  will get hot 

         during use. 

 

6.

If a socket outlet is used do not position the outlet immediately behind the heater. 

 

7.      Avoid the use of an extension cord with this product. 

 

8.      Do not cover or obstruct the heater while it is in use. 

 

9.      Do not insert any object through any slot or opening in the heater. 

 

10. Do not use if guard is not present. 

 

11.   

WARNING

 - When replacing the emitter or cleaning the unit, ensure that the 3-pin 120 

         volt plug is removed from its socket outlet or if hard wired circuit is disconnected from the 
         mains supply. 

Note

: always ensure that the emitter is cool before handling. 

 

12. Do  not  handle  the  halogen  emitter  with  bare  hands.  If  it  is  inadvertently 

touched,  remove  finger  marks  with  a  soft  cloth  and  methylated  spirit  or      
rubbing alcohol. Otherwise, the marks will burn into the quartz emitter during 
use causing premature heater failure. 

 

13.    The  heater  is  not  intended  for  use  by  young  children  and  must  be  supervised  by  a       
         responsible person at all times. 

 

14.    Always remove the 3-pin 120 volt plug on the 120 volt heater if it is not being used. 

C A U T I O N

C A U T I O N

C A U T I O N

C A U T I O N  

I N T R O D U C T I O N

 

 

The Alpha H1 heater produces radiant heat like the sun, warming people and objects rather 
than  the  air  in  between.  It  is  mounted  on  an  adjustable  bracket  that  allows  the  heat  to  be     
directed exactly where it is required. The Alpha H1 can also be used in a modular system in 
that more than one heater can be joined together - see ‘Configurations’ later in the manual. 
The Alpha H1 weatherproof heater is designed for indoor and outdoor use. 
 

Please read the following instructions carefully before use. The safety of this heater is      
guaranteed only by its correct usage in accordance with these instructions, therefore 
they should be retained for future reference.

 

Содержание SALPHA10240

















Отзывы: