Infineon XENSIV BGT60TR13C Скачать руководство пользователя страница 37

Страница: 37 / 59

37 of 59

2022-23-05

User Guide for XENSIV™ K

IT CSK BGT60TR13C

Table of contents

Figure 34

Rapid IoT connect developer kit top and bottom views

CYSBSYS-RP01 module:

Rapid IoT connect module containing PSoC™ 6 MCU and Wi

-Fi Bluetooth® radio

with a chip antenna.

17.2032Mhz ECO

: External Crystal Oscillator (ECO) for PSoC™ 6 MCU.

JTAG header

: A 10-pin external programming header is provided to use external programmers like

MiniProg4 to program the PSoC™ 6 MCU device over the SWD interface. This header is not loaded by default.

Expansion headers (J1, J5)

: These headers provide connectivity to PSoC™ 6 MCU GPIOs, and are

compatible with Adafruit Feather pin mapping.

User button

: Used for the user application. The PSoC™ 6 MCU pin is connected to power; when the push

button is pressed, the PSoC™ 6 MCU pin is grounded.

Chip antenna (A1):

An ultra-miniature chip antenna that supports 5GHz and 2.4GHz bands.

3.3V regulator:

Regulator used to power the analog domain of PSoC™ 6 MCU.

Power LED (LED4)

: Blue LED that indicates the status of power supplied to the board.

Charging LED (LED5):

Yellow LED that indicates the LiPo battery charging status by glowing continuously. If

the LiPo battery is not connected, this LED does not glow. If the board is powered solely from the LiPo
battery, this LED does not glow.

10.

USB connector

: The USB cable connects between this USB connector and the PC, used to power the entire

board as well as the connection to the on-board KitProg3 programmer/debugger.

11.

User LED (LED2

): Active LOW red LED, so the PSoC™ 6 MCU pin must be driven to ground to turn ON the LED.

12.

KitProg3 status LED (LED3)

: Yellow LED (LED3) that indicates the status of KitProg3. For details on the

KitProg3 status, see the "Programming and Debugging" sub-section in the "KitProg3: On-board
programmer/debugger" section of this document.

13.

Battery connector (J3)

: Used for connecting a 3.7-V LiPo battery.

Содержание XENSIV BGT60TR13C




























































Результаты поиска

Содержание XENSIV BGT60TR13C

Отзывы:

Бренды по названию

Популярные бренды

Infineon XENSIV BGT60TR13C, Руководство пользователя

Результаты поиска

Содержание XENSIV BGT60TR13C

Отзывы:

Бренды по названию

Популярные бренды