Infineon TLE984 QX Series Скачать руководство пользователя страница 467 | Manualshive

Страница: 467 / 972

background image

User Manual

467

Rev. 1.1

2019-03-18

TLE984xQX

Microcontroller with LIN and Power Switches for Automotive Applications

General Purpose Timer Units (GPT12)

16.4

Timer Block GPT2

From a programmer’s point of view, the GPT2 block is represented by a set of SFRs as summarized below.
Those portions of port and direction registers which are used for alternate functions by the GPT2 block are
shaded.

Figure 102 SFRs Associated with Timer Block GPT2

Both timers of block GPT2 (T5, T6) can run in one of 3 basic modes: Timer Mode, Gated Timer Mode, or Counter
Mode. All timers can count up or down. Each timer of GPT2 is controlled by a separate control register TxCON.
Each timer has an input pin TxIN (alternate pin function) associated with it, which serves as the gate control in
Gated Timer Mode, or as the count input in Counter Mode. The count direction (up/down) may be
programmed via software or may be dynamically altered by a signal at the External Up/Down control input
TxEUD (alternate pin function). An overflow/underflow of core timer T6 is indicated by the Output Toggle
Latch T6OTL, whose state may be output on the associated pin T6OUT (alternate pin function). The auxiliary
timer T5 may additionally be concatenated with core timer T6 (through T6OTL).
The Capture/Reload register CAPREL can be used to capture the contents of timer T5, or to reload timer T6. A
special mode facilitates the use of register CAPREL for both functions at the same time. This mode allows
frequency multiplication. The capture function is triggered by the input pin CAPIN, or by GPT1 timer’s T3 input
lines T3IN and T3EUD. The reload function is triggered by an overflow or underflow of timer T6.
Overflows/underflows of timer T6 may also clock the timers of the CAPCOM units.
The current contents of each timer can be read or modified by the CPU by accessing the corresponding timer
count registers T5 or T6, located in the SFR space (see

Section 16.4.8.1

). When any of the timer registers is

written to by the CPU in the state immediately preceding a timer increment, decrement, reload, or capture
operation, the CPU write operation has priority in order to guarantee correct results.
The interrupts of GPT2 are controlled through the GPTM1IEN and GPTM1IRC. These registers are not part of
the GPT2 block.
The input and output lines of GPT2 are connected to pins. The control registers for the port functions are
located in the respective port modules.

mc_gpt2_registers.vsd

Data Registers

Control Registers

T5CON

Interrupt Control

Tx

GPT2 Timer x Register

CAPREL

GPT2 Capture/Reload Register

TxCON

GPT2 Timer x Control Register

TxIC

GPT2 Timer x Interrupt Ctrl . Reg.

T5

T6

T5IC

T6IC

CAPREL

T6CON

CRIC

KSCCFG

Miscellaneous

PISEL

ID

KSCCFG

Kernel State Configuration Register

PISEL

Port Input Select Register

ID

Module Identification Register

«
...
465
466
467
468
469
...
»

Содержание TLE984 QX Series













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TLE984 QX Series

Бренд: Galcon Страницы: 32

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: HW Group Страницы: 18

Бренд: Securi-Prod Страницы: 3

Бренд: S&C Страницы: 26

Бренд: Barco Страницы: 4

ESP32-C3 Series

Бренд: Espressif Systems Страницы: 30

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

Бренд: 4IPNET Страницы: 11

Бренд: E+L Страницы: 62

Бренд: Omicron Страницы: 17

Бренд: Simplex Страницы: 12

Бренд: Walchem Страницы: 35

Бренд: AL-KO Страницы: 52

Бренд: Belimo Страницы: 4

Бренд: Astralpool Страницы: 27

Бренд: Air Torque Страницы: 11

Бренд: Danfoss Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды