manualshive.com logo in svg

iNetVu 1201 Flyaway, Руководство по устранению неисправностей, Страница: 66 / 71

Поделиться
Скачать
iNetVu 1201 Flyaway Скачать руководство пользователя страница 66

iNetVu Troubleshooting Guide - 1201 Flyaway 

 

Page 66 of 71 

  

3. 

To troubleshoot an 

IP

 (HTTP, TELNET, UDP, SNMP) configuration: 

 

•

  Verify the controller and modems IP and (Password/CD-KEY if required) are correct. 

•

  Try to ping the modem. 

•

  Connect the Modem directly to the Controllers Ethernet port bypassing any routers, hubs or 

switches. 

•

  Attempt to login to the modem via Telnet. This will verify IP address and Password. 

•

  Swap out the Ethernet cable. 

 

TCP/IP Connection Software Configuration (HTTP, TELNET, UDP, SNMP) 

 

 

4. 

You may experience an issue were the transmitter is being automatically disabled. This will 
occur when 

Automatic Tx Disable

 is turned on and there is a intermittent communication 

issue between the controller and the connecting device. Bypass any routers, hubs or switches 
and connect directly to the controller with a new Ethernet cable. This should resolve the issue 
and indicate you have a routing or cabling failure. 

 

Please contact C-COM Technical Support at 

[email protected]

 for further assistance. 

Automatic Tx Disable 

If this checkbox is selected, the controller 

will automatically disable the transmitter if a 

reset is done to the modem during 

transmission and communication between 

the controller and modem is re-established.

 

Содержание 1201 Flyaway








































































Отзывы:

Нет отзывов