iNetVu 1201 Flyaway Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 71

iNetVu 1201 Flyaway Скачать руководство пользователя страница 61

iNetVu Troubleshooting Guide - 1201 Flyaway

Page 61 of 71

RF Signal Not Being Detected (Powering LNB from the Modem)

Step 2:

•

Our next step is to test voltage on the hardware to determine if our power source is making it
all the way up to the LNB.

•

Starting with the Modems “RX IN” port disconnected the coax cable and using a volt meter to
determine if the modem is outputting voltage. Please check with your ISP or satellite modem
provider to determine what the normal output should be. If no voltage is displayed, please
exchange modem. If proper voltage is displayed, reconnect the cable and proceed to step 3.

Step 3:

•

Disconnect the coax cable from the splitters “OUT” port coming from the “Power Pass”.

•

Measure voltage on this end of the cable. If the voltage does not match the output from the
modem then replace the cable. If the voltage does match, please connect the cable back and
proceed to step 4.

Step 4:

•

Disconnect the coax going into the “IN” port of the splitter as shown below.

•

Measure voltage on the port. If the voltage does not match the output from the modem then
replace the splitter. If the voltage matches, please reconnect the cable and proceed to step 5.

Step 5:

«
...
59
60
61
62
63
...
»

Содержание 1201 Flyaway








































































Отзывы:

Нет отзывов