iNetVu 1201 Flyaway Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 71

iNetVu 1201 Flyaway Скачать руководство пользователя страница 46

iNetVu Troubleshooting Guide - 1201 Flyaway

Page 46 of 71

Error 0x9008 - PL Jam Error

1. If the Mobile Platform doesn’t physically move

Possible Causes:

•

7000 Controller

•

5 Amp Fuse

•

Flyaway Control Cable

•

Internal Wiring

•

Polarization Motor

a.

Verify if 7000 Controller is outputting 24VDC. Disconnect the motor cable from the back of the
controller, place the volt meter leads on pins 4 and 6 of the controller. Using the 7000 controllers
front panel, select Polarization with HI SPEED ON and hold +. Are you getting 24VDC?

b. If we are not getting voltage from the 7000 controller

, please turn off the controller and verify

the 5A fuse has not blown. If the fuse is blown replace it and try again. If the fuse is not blown,
contact C-Com Technical Support for further assistance.

Warning High Voltage:

Always remove power from the 7000 Controller prior to removing fuse.

Failing to do so can result in personal injury or damage to the controller.

«
...
44
45
46
47
48
...
»

Содержание 1201 Flyaway








































































Отзывы:

Нет отзывов