background image

INSTRUCTION

 

i

Read this instruction before installation 

and wiring of the product

CMF5U

Consult documentation in all cases where this symbol 

is used, in order to find out the nature of the potential 

hazards and any actions to be taken

1

CMF5U

Controller with display

 

CMF5U is a pre-programmed, configurable controller. It has 5 inputs/
outputs and can be configured to control temperature, CO

2

, humidity 

or pressure. All configuration and normal handling is done using the 
display and the knob on the front. From revision R18, it is possible to 
connect an external PT1000 setpoint device.

Technical data

Supply voltage 

 

24 V AC ±15%, 50...60 Hz

Power consumption 

3 VA

Ambient temperature 

0...50°C

 

Ambient humidity   

Max. 90% RH

Storage temperature 

-20...70°C

Display 

 

Numeric / graphic. Background 

 

 

 

illumination.

Inputs/outputs 

 

Refer to connection illustrations and 

 

 

 

table below

Terminal blocks   

Disconnectable, so-called lift type for    

 

 

cable cross-section max 2.5 mm

2

Protection class   

IP20

Material, casing   

Polycarbonate, PC

Weight 

 

215 g incl. terminal blocks

 

Dimensions 

 

122 x 120 x 64 mm (WxHxD incl. terminals,  

 

 

fixed installation)

 

Pollution degree   

2

Temperature settings

Temperature, supply air  

-20..+60, 20...100, 60...140°C

 

Setpoints 

 

-18...+60, 22...100, 62...140°C

External setpoint   

0...40°C

 

Neutral zone  

 

0...10°C

 

P-band 

 

0…99°C

 

I-time 

 

0…990 s

 

Min. limit damper   

0…99%

Other settings

Setpoint values

 

   CO

2

 

 

0...100% of max set value on UI1

 

   General (GEN)   

0...100% of max set value on UI1

 

   Pressure (Pa)   

0...100% of max set value on UI1

Scaling of UI1

 

 

0...10 V DC in

 

   CO

2

 

 

10...9900 ppm

   General 

 

0...100%

   Pressure 

 

100 Pa...2500 kPa   

 

 

Neutral zone

 

 

12.5% of max

P-band

  

 

   CO

2

 

 

0...100% of UI1

 

   General (RH) 

 

0...100% of UI1

 

   Pressure (Pa)   

0...300% of UI1

 

I-time

 

 

0…990 s

Control setting 5 

Outdoor compens. start 

-20…+60°

C

Setpoint pressure at

 

-20°C outdoor temp. 

0 Pa...2500 kPa

Installation

CMF5U must be mounted in a DIN-standard casing (minimum 7 
modules) or in a cabinet, either on a DIN-rail or, using the two screw-
pockets provided, by being screwed to any suitable flat surface in the 
cabinet. The controller can also be mounted in a cabinet door or other 
control panel, using a suitable front-mounting kit (CMF-KIT).
The controller must be connected to a 24 V AC safety insulating 
transformer providing mains insulation.

Follow table 1 below for connection. 

Table 1. I/O connection terminals. Terminals 2, 20 and 50 are internally con-
nected.

Terminal Designation Operation

1

G

Supply voltage 24 V AC

2

G0

3

20

AGnd

Ref. for AO1 and AO2

21

AO1

0...10 V DC Output

22

AO2

0...10 V DC Output

41

DI+

Reference for DI1

42

DI1

Digital input

43

UI+

Reference for UI1 digital mode

44

UI1

0...10 V DC or Digital input

50

AGnd

Ref. for AI1, SPI and UI1 analogue

51

AI1

PT1000 temp. sensor input

52

SPI

Input PT1000 setpoint device

 

Digital inputs DI and UI are only intended to be used with a 

potential-free contact or switch.

 

If the CMF5U and active sensors and 

actuators connected to it share transformer, it is essential that the 
same transformer-pole is used as reference for all the equipment. 
Failure to do so will prevent the equipment from functioning as 
intended and may also lead to damages.

For best protection against disturbances, a shielded twisted-pair cable 
should be used for wiring the sensors. Ground the shield at one end.
The protection provided by the equipment may be impaired by im

-

proper use.

 

MA

Y 14

EN

Содержание CMF5U















Отзывы: