background image

System1000_GB_130705.doc  

Page 

13 

20.  Guarantee Conditions 

The following conditions that describe preconditions and extent of our guarantee leave the dealer’s 

warranties according to the purchase contract untouched. 

Before sending a product back or handing it to your dealer, please contact our helpline to discuss the 

problem in advance. Maybe your problem can be solved by phone. 

We offer the following guarantee to the first purchaser of this product: 

According to the following conditions (No. 2-7), we will repair any damage caused to the product 

due to faulty workmanship, if it was reported to us immediately after noticing and within 24 

months from delivery. This guarantee does not apply to minor differences from standard quality 

that are irrelevant for value and performance capability of the product and to damage resulting 

from chemical or electrochemical effects of water or abnormal environmental conditions. 

We will repair free of charge faulty parts or, at our discretion, exchange them for faultless parts. 

Exchanged parts will become our property. 

The guarantee expires, if repairs or modifications are carried out by unauthorized persons or if our 

products are provided with accessories that are not suitable for them. The guarantee also expires if 

modifications of original parts are carried out. 

Repairs or exchanges carried out under guarantee do not extend the guarantee period and do not 

start a new guarantee period. The guarantee period for spare parts ends with the guarantee period 

for the complete product. 

The guarantee is always limited to the customary price of the product. 

Further claims, especially claims for damages that occur to persons or things other than the product 

are excluded, as long as no liability is ordered by law. No compensation can be claimed in the case 

of burglary or failure of the product. 

Please send the faulty product free of domicile. Shipments that are not free of domicile will not be 

accepted. Repairs can only be carried out if an explicit description of the faults is supplied. Please 

send in only complete systems that are well packaged. 

 

NOTE: An alarm system can only be seen as a supplement to mechanical security measures. It is no 

substitute for your duties of care and for sufficient insurance cover. 

 

 
21. Appendix: Wirefree Door-Contact 1000 M (optional) 

The optional door contact can be used to secure single doors or windows. The door contact contains a 

reed contact that is closed by a magnet on the opposite side. If the magnet is removed, the contact 

opens, and an alarm signal is transmitted to the siren. 

 

 

21.1. Coding 

 

When you receive the door contact, it is not factory preset to any special code. Please follow the 

instructions on the packaging of the door contact 1000 M to adjust the code to your system. 

 

 

21.2  Fitting the Battery 

The door contact is supplied with a battery. To operate the door contact, slowly pull out the protective 

tab. (If this is difficult, loosen the screws at the back of the casing, and retighten them after pulling out 

the protective tab.) 

 

 

 

 

  

    

 

 

 

 

fig. 21

 

Содержание 1000 R

















Отзывы: