Indesit WD 125 TS, Инструкция по установке и эксплуатации

Страница: 20 / 32

L M
A
B C I D
G
H
E
F
Easy iron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron.
You can use it with programmes
2-3 (Cotton), 4-5 (Synthetics)
and 8 (Delicates).
Press this button in
programmes
4-5-8 and the wash
cycle will come to a stop on
symbol
. You can complete it
by pressing button E again.
Note: If you also want to run the
drying cycle, this button is
enabled only if combined with
level ( Iron ).
Slow spin
Use this button to reduce the
spinning speed from 1200 to
600 rpm for the cotton and linen
programmes and from 850 to
600 rpm for the synthetic
fabrics programmes.
Rapid wash
This button reduces the length
of the wash programme by
about 30%. It cannot be used
with special programmes (see
page 18) or those for wool and
silk.
Prewash
With this button, you can pre-
wash on all programmes except
the wool programme and the
special programmes (see page
18).
Here I’m in command
Understanding the control panel
Making the right choice is important. And it’s easy.
Programme selector knob
and programmed start
Use this knob to select the wash
programme.
Turn this knob clockwise only.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the knob.
Now press on/off button I (position
I
), pilot lamp L will start flashing.
After 5", the setting will be
accepted, pilot lamp L will stop
flashing (staying lit) and the wash
cycle will begin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols
(Stop/Reset) and wait
5" : when the cancellation has
been accepted, pilot lamp L
flashes, and you can then turn the
appliance off.
You can use this knob to delay
the appliance's operation.
Select one of the 4 delay time
positions, press the on/off button
I (position
I
) and wait 5". The
setting has now been accepted
(pilot lamp L stays lit) and you can
select the programme you desire.
Pilot lamp L has a particular
flashing motion (2" on and 4" off)
to indicate that a delayed start
has been set.
During this phase, you can open
the appliance door and change
the washing load, should you
wish to do so.
After the wash cycle has been set
and accepted by the washer-
dryer, turning the knob will have
no effect (except for when it is on
position Stop/Reset).
Temperature control knob
It is used to set the wash tempe-
rature in the recommended
programme table on pag. 18. It
also allows you to reduce the tem-
perature recommended for the
selected programme, and even to
set a cold wash cycle (
).
Drying cycle knob
Use this knob to select the
desired dr ying cycle. Two
options are available:
A - Based on time:
From 40 minutes to 150.
B - Based on the damp level of
the dry clothes:
Iron
:slightly damp clothes,
easy to iron.
Wardrobe
: dry clothes to
put away.
Extra dry
: very dry clothes,
recommended for towelling and
bathrobes.
A cooling stage is foreseen at
the end of the drying cycle.
Detergent dispenser
It is divided into 3 compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle
wash;
3. Fabric conditioner.
17
Instructions for installation and use
On-off
When button I is pressed, the
washer-dryer is switched on,
when it is not the machine is
switched off.
Turning the appliance off
does not cancel the selected
programme.
On-off lamp / door locked
Lamp L flashes slowly when the
appliance is switched on and
awaiting instructions and at the
end of a cycle, indicating that the
door can be opened. It flashes
quickly when the door should
not be opened. A steady light
means the appliance has
accepted the selected
programme.
Drying cycle lamp
When this lamp is on, it means
that knob C has been set on a
drying cycle and at the end of
the wash cycle, the appliance
will run the selected tumble
drying cycle.
The detergent dispenser is here.
1
2
3