background image

Service Manual

Manual LFT 114 - 116 - 216

Edition

2007.10.15

Language

English

22

CHAPTER 8:   DISMANTLING

Detergent Dispenser:

1.

Unfasten the 2 screws placed on the sides of the innerdoor and remove the Frontpanel.

2.

Unfasten the 2 screws placed infront of the door, behind the external finished panel.

3.

Disconnect the dispenser cables and unscre the 6 screws that fix it to the inner door-panel.

4.

Remove by lifting the dispenser from the inner door-panel.

Display Board:

1.

Unfasten the 6 screws placed on the inner-door panel.

2. 

Disconnect the cables from the display-board.

3. 

Press by means of a flat-tipped screw-driver the “wedge” which fixes a group of commands of the board-display, 
in order to remove it by lifting it.

4. 

Repeat th whole procedure with the screw-driver on the other “wedge”, in order to remove the support.

Inner-Door and Hinges

1.

Proceed dismantling the front-panel.

2.

Proceed dismantling following steps described in dismantling the display-board

3.

Insert a screw-driver in the hinge-hole (on both sides of the machine) in order to block the half-open door
(for safety reasons)

4.

By means of pliers, remove the 

tirante 

by making it turn in the hole where it is fixed.

5.

Remove the ground-fastonwhich is connected to the hinge.

6.

Unfasten the 4 lateral screws (2 on each side) that fix the hinges on the inner-door and remove.

7.

Remove the inner-door by lifting it.

8.

Disconnect the ground-fastons on the hinges.

9.

Unfasten the screws (one on the left and one on the right) in the machine, which fix the hinges onto the wash-basket.

10.

Unfasten the 4 screws (2 on each hinge), fixing the hinges onto the base of the dishwasher.

Pressostat

1. 

Unfasten the 4 screws (2 on the front and 2 behind) fixing the side-panel to th back of the machine.

2. 

Unhook the panel with the aid of a flat-tipped screw-driver (2 hooks are present: one is on the front of the machine
an one is at the back.

3. 

Remove the pressostat with the aid of a flat-tipped scre-driver.

4. 

Disconnect the pressostat cable.

NB: Care must be taken that th tube is correctly positioned back onto the hooks   whn assembling the pressostat .

Floating-ball

1.

Remove the board taking care not to disconnect the cable.

2.

Unhook the floating-ball by unfastening the hook and removing it in the direction of the water-collector.

3.

Disconnect the connector of the floating-ball.

Noise-proof filter and Support:

1.

Unfasten the 4 screws (2 on the front and 2 at the back) fixing the lateral right-hand side panel.

2.

Pull out the filter by moving it along the support-grooves.

3.

Disconnect the nise-proof cable.

4.

Insert a small screw-driver or tester in the hole positioned next to the support in order to lift the hook fixing the
support in place, and allow it to slide in the direction indicated by the arrow. 

NB: Pay caution to the cable when dismantling and re-assembling.  

Содержание LFT 114 UK


























Отзывы: