4
GB
E
lectrical
connection
Power supply voltage and frequency: 230-240V a.c.
50Hz.
the supply cable must be positioned so that it
never reaches at any point a temperature 50°C
higher than the room temperature. The cable must
be routed away from the rear vents. Should you
require it, you may use a longer cable, however, you
must ensure that the cable supplied with the
appliance is replaced by one of the same
specifications in accordance with current standards
and legislation.
Your appliance is supplied with a 13 amp fused plug
that can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
W
A
RNING
-
T
H
IS
A
PPLI
A
NCE
M
UST
BE
E
A
RT
H
ED.
T
H
E
FOLLOWING
OPER
A
TIONS
S
H
OULD
BE
C
A
RRIED
OUT
BY
A Q
U
A
LIFIED
ELECTRICI
A
N.
R
e
p
lacin
g
t
h
e
fus
e
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
R
e
p
lace
m
ent
fus
e
co
v
er
s:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
R
e
m
o
v
in
g
t
h
e
p
l
ug:
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a cable
extension or to re-route the mains cable through
partitions, units etc., please ensure that either:
the plug is replaced by a fused 13 amp re-
wireable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
Please note:
for appliances with a rating greater
than 13 amp (eg: electric hob, double ovens and
freestanding electric cookers etc.) the mains cable
must be wired into a cooker output point with a
Gas
connection
The cooker should be connected to the gas-supply
by a corgi registered installer. During installation of
this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the
convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed Adaptation to different gas
types. On some models the gas supply can be
connected on the left or on the right, as necessary;
to change the connection, reverse the position of the
hose holder with that of the cap and replace the
gasket (supplied with the appliance). In the case of
connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The
gas supply must be connected to the left of the
appliance. Be sure that the hose does not pass
through the rear of the cooker touching hot parts.
m
a
k
e
su
re
t
h
e
supp
l
y
p
re
ssu
re
con
f
or
ms
w
it
h
t
h
e
v
al
u
e
s
sh
o
w
n
in
t
h
e
ta
b
le
entitle
d
C
aracteri
s
tic
s
o
f
t
h
e
b
u
rner
s
an
d
no
zz
le
s
.
When the cooker is installed between cabinets
(recessed), the gas connection must be effected
by an approved flexible hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for the
cookers is a threaded G 1/2 gas female fitting.
C
onnectin
g
t
h
e
g
a
s
supp
l
y
To make the connection, a
flexible hose should be used
corresponding to the current
gas regulations which are:
the hose must never be at
any point in its lenght in
contact with the hot parts of
the cooker;
the hose must never be longer than 1,5 metre;
the hose must not be subject to any tension or
torsional stress and it must not have any
excessively narrow curves or bottlenecks;
the hose must be easy to inspect along its entire
length to check its condition;
the hose must always be in good condition, never
attempt to repair.
the installation must comply with gas safety
(installation and use) regulations 1984. In all cases
for the above, by low, a qualified, corgi approved
engineer must be called for installation.
HOT PARTS
600 mm
